old factory worker 3d models

I have printed the faceplate above and will be using it but will wait till I need to take the old one off. the others are not as out of alignment. Added another 40 mm fan this one aligns it much better at least with the microswiss. Added 4 belt...

I'm trying to delete the old photos and stl files but I can't so don't use those. Please print responsibly! This is in no way meant for real firearms and only as a prop or for backyard airsoft. I don't recommend fielding this unless you print in...

This allows for a pretty easy fit for the old A8 heat break tube on the stock extruder. So I use that heat break, along with some longer PTFE on my V6Lite, to create a closed direct feed between the extruder gear and nozzle tip (the heat break and...

These cells are what keep the memory working for saved games. The idea is that when one battery starts dying you can easily add a new one before removing the old one or you can use two batteries and have them both last a bit longer. This pack also...

If the stronger/ more robust version is still required, then it can be downloaded from the above link, although it may take marginally longer to print.By attaching a strip of 9mm clear double-sided adhesive gel tape to the flat panel on the back of...

With the Slider/carriage removed, remove all other hardware from the old parts. Install Procedure After removing a carriage, bolt the Top wheel on first since part of that screw head is covered by carriage. Add 10mm micro-adjust limit screw & jam nut...

Ensure your scope is ten years old and check the photo to confirm you have the same type of focuser. It comes with a focuser-to-motor pin adapter and a wheel. The previous pin adapter was not up to the task: the teeth on the motor axis eventually...

Current options are either unreliable (laser sensors don't work well with transparent filaments) or expensive and finicky (Duet magnetic filament monitor) So my idea was to use a $0.50 optical end-stop to sense pulses through an encoder wheel, just...

 When it became time for the old Grand Master to stand down, Kang was uncontested to take his place and unanimously welcomed by his fellow monks. Incredulously inside, situated at all corners and growing out from the stone floor, were trees full of...

This is basically an old 12v wall-wart I found in my drawer, an adjustable buck convertor and a volt/amper meter - together they become a very usable power supply for my crazy electronic projects. This adjustable power supply has 2 banana terminals...

As an alternative to the float, use straw or pine needles, or a piece of non-slip shelf liner (thanks for the idea, @milsimlabs): https://www.amazon.com/DAZZ-8714388-Taupe-Classic-Shelf/dp/B01LWASQEE/ The honeycomb scad library is from @pruby's...

I used old nets, screens, etc. to do some of the scale-like effects and painter's tape for most of the stripey patterns. I hand-painted the eyes with acrylic and enamel paints. After the painting was done, I inserted the wires. I ran a straight...

The design is old, and printers were not always what they are today, as a someone who has gone through many generations of printers this is very common. The problem, newer printers are much better at bridging than they used to be, as well as new...

His sole objective: to create mighty weapons that would rival even those wielded by the heroes of old. The Head Because this massive weapon and most common printers are limited to 8"x 8" x 8", the entirety of this prop has been processed to fit...

*NOTE: I have added an improved version of the bellows with more rounded corners that lasts a lot better than the old design when printed in TPU filament.* Designed in Fusion 360. ...I don't provide the design file as a few unscrupulous people have...

*I used the old PIKO couplings, I think there are similar ones from Fleischmann still available with the T-shaped head. I found a printable (I didn't tested it) version from [wsvenny on...

The other is a tool less latch which holds the clamp together using a M3x(>20)mm screw, two M3 nuts, and a spring from a regular old pen. The piece that holds the microphone is separate, which allows the whole clamp to be stored in a more compact...

* Remove old Extruder assembly (search for instructions if you don't know how), but leave the metal X-Carriage plate as it is. * Attach "Hemera_Base" part to the original metal X-Plate of the Ender 5 (Plus) with two M3x8mm screws, just like in the...

I've also put the old f3d files back, since they behave a bit differently when out of range parameters are put in, see the comments for more detail.) (edit 3/24/2019, I've added an f3d file for customizing the o-ring.) This rugged box features hinges...

The goal, to accomplish even, smooth filament delivery from random samples or loose ends of old spools.The Sample Spool project was created out of necessity. I have a LOT of filament samples laying around. I want to use them, but I have no good way...

I imagine they could be cannibalized from ballpoint pens or old spare blasters if you have any of those laying around. If you're into modding, a stock blaster catch/trigger/lock spring could also do the trick provided it's the right length. More...

6mm                             (or you can use 3d printed Optional button )                           ...

You will also need one of the old o-rings from your loop connections at the T pieces for each insert you decide to build (there are 2 per loop hose, these only use one). This is optional, since the whole idea here is airflow, but.. it's still a...

I use the word loft here liberally because in this model it's just a square blue box set to variable a and b… (FreeCAD blue lines in sketcher are reference geometry) Old walk through for CAD continues below END UPDATE 9/9/2017 Steps for making this...

The old red LEDs I found in my spares box are a bit taller by about 1mm than the originals, so adjust the value LED_DEPTH_FROM_TOP to suit. The PDP-11/03 requires just one of these receptacles. It is also used in the PDP-11/05 where seven are...

It was designed with my old printer in mind (which had horrible tolerances). The design is also imperfect, with the “spring” wearing down over time and it overall running roughly. I apologize for the inconvenience. This will not be deleted as I still...

... to the class. I also included a link to a YouTube video that does an excellent job of explaining gear systems even though it is on the old side. These two resources will help give the students some background information on gear trains and systems.

Tinkercad link: https://www.tinkercad.com/things/4X0lBq4EURd Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool https://www.thingiverse.com/thing:4654396 - Rivet Placement Tool...

Material info: METAL_SANDY_DIRT___OLD_v2.spsm (Extract from archive to smart-materials folder) Weapon Metal.spsm (Extract from archive to smart-materials folder) Dirt.spsm (Default smart-materials) Steel Rust Surface.spsm (Default smart-materials)...

I sacrificed an old wired USB mouse to get its lightweight four-conductor wire and used the remaining strip of six LEDs as a center light. The LED strip has pads labeled +5v, G, R, B for Power, Green, Red, & Blue (RGB) between each LED segment. The...