office signs 3d models

Designed these small placards so they could be held with velcro to the office door. ...This was mainly to help stop people from barging in because of COVID.

2mm x 2in x 8in Office sign

Simple office sign for my wife´s translation agency :-) in Fusion 360.

Minions the Office sign

This a The Office sign witch says ``IDENTETY THEFT IS NOT A JOKE JIM!``

Office sign First colour: to 0.8mm white Second colour: 1mm on Blue

Ready to print The Office sign, with perfect topology, and high resolution of polygon. ...Comes in the following formats: .Stl .Obj Have fun :)

This is a Remix of The Office Sign by jakestaby. ... This remix has a "string" thingy, i thought it would be nice and i made one with screw hole and one without screw.

This is a Remix of The Office Sign by jakestaby. ... This remix has a "string" thingy, i thought it would be nice and i made one with screw hole and one without screw.

Here is my attempt at creating the The Office sign, and my first attempt at modelinganything. I'm using two separate processes, but a pause between layers should also work. If you aren't squishing your first layer, you should change the filament at 2...

... just the holders have been stripped. ... Depending on your printer it could beneficial spit The_Office_Sign_B.stl into small parts, PrusaSlicer is very handy for that, and then printed them individually (sequence).

It has now been fixed. After messing around with some of the other The Office signs, none of them were quite right. Here is my attempt at creating the The Office sign, and my first attempt at modelinganything. I'm using two separate processes, but a...

I experimented with several other The Office signs but none of them matched my expectations. Here is my attempt at creating a custom The Office sign, and I'm proud to say it's my first try at 3D modeling. To achieve this result, I've employed two...

I've simplified the design to make it work without dual extrusion, focusing on creating a clean look for The Office sign that doesn't require excessive complexity. Since most people don't have dual extrusion printers, I've adjusted the parts...

Remix of jakestaby's and Lyl3's "The Office"-type signs. I decided I needed one for my home office, so.... You can start the white filament on layer 11. If you are unsure how to do multiple filament colors with a single-extruder printer (I was...

The Signs: The signs are 20cm long and require approximately 9 meters of 1.75mm filament to be printed, with a 20% infill setting that should work just as well with less infill. You can choose to print one sign or both. Hooks: I didn't measure the...

I created this sign to direct students to my school's guidance office. The head of our counseling department asked for help due to inadequate directions from the entrance. ...To accommodate the CR-10 printer's limitations, I modified the sign's...

LECTERN OFFICE SIGN-IN STAND

LECTERN OFFICE SIGN-IN STAND

I thought it would be fun to make a sign for my office that said the "The Office". I printed it with PLA. Obviously, it will work best if you can swap filaments half way through the print. On my Prusa, I printed black on the bottom and white on...

The original sign can be found can be found on: https://www.thingiverse.com/thing:3118823 The issue was that the part in the link above is whole so either you'll need to paint it black & white after it's done or you'll have to pause the print in the...

The original sign can be found can be found on: https://www.thingiverse.com/thing:3118823 The issue was that the part in the link above is whole so either you'll need to paint it black & white after it's done or you'll have to pause the print in the...

Here's a replica of that sign you see on the TV series "The Office," which I carefully crafted using Blender. ...It was my initial foray into designing and printing 3D models, so I'm thrilled to share it with you!

There are also teeny-tiny holes in the top of the sign so that you can hang it from a tiny string on your wall, or you can simply prop it up on your desk in your office ; ) Hope you absolutely love it. ...(Note: This is a dual extrusion print) Print...

Sign for the 3D printer's room

This sign is intended for a desktop monitor or cubicle. I can do personalize signs if needed.

I remixed the sign so i could print the sign in 2 separate pieces and then glue the withe part in the base more easily.

I remixed the sign so i could print the sign in 2 separate pieces and then glue the withe part in the base more easily.

Just a fun project to create a door sign for a home office. Designed to be two-color printed with filament switching. Mount it on a door or wall with double-sided tape.</p> <p>The OnShape 3D CAD file for this is located here:</p> <p><a...

Print the sign letters facing down and insert a filament change on the layer that is visible inside the letters and the one below.It looks best when there are two layers of color.You can glue in 3 Magnets or mout it with double sided tape.Blank...