off white4 3d models

In order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of the character’s outfit seams and the guitar strap was taken off the figurine’s shoulders. For you to achieve the...

Because of this, additional cables glued to the flat ribbon cable came off very quickly in every attempt. ...

The wiring comes out of the pad slightly off-center, so it's neatly guided to the back of the machine without interfering with the bed mounting point at the back. For 220V Heat pad users, grounding point at the bed and fully isolated bed from the...

This 3 wires is going into the ESC directly from the pipe side, the ESC other side is motor connections, cut the motor cables for the needed length. Check that thelow rpm protection is off in the ESC's (for low kv motors what we use it is...

Instead, I cut the filament off where it enters the extruder and just start a load filament process on the printer. It extrudes the filament left inside the extruder and I just feed in the new spool of filament following it. If you use this method...

In order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of Pippin’s clothes seams and his cloak was “taken off”. All the assembly parts come in STL files in recommended positions...

Using the I-beam would allow me to put little supporting wheels on the sides so there is no way for the treadmill to fall off.As a diameter I chose 120cm, simply seemed like good dimension based on commercially available ones.Also - I didn’t wanted...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above. Support enforcers are neededNo gluingEasy to printDesigned on...

The supervillain’s long cape has also been taken off the figurine’s back and comes as separated 3D printing part that is to be inserted along the suit’s pattern. All the assembly parts come in STL files in recommended positions that were worked out...

Ever since hulking lawman Hobbs (Johnson), a loyal agent of America's Diplomatic Security Service, and lawless outcast Shaw (Statham), a former British military elite operative, first faced off in 2015's Furious 7, the duo have swapped smack talk...

For you to receive the cleanest result possible the pulveriser that Liquidator is holding was extracted from both hands and provided as a separate part, the strapped bag was “taken off” the figurine as well as a tank that the man is wearing on his...

Put it back in its place and wait until the glue is dryed.Then strip the isolation tape off and go on to the next step.Touchpad  Remove the backside of the touchpad. Take the hot glue gun and make a big drop of hot glue at the place for the...

Once this is done the top part of the frame should come off.The bottom part of the drybox and the panels can be set aside as we will work with the top frame first.Finally, remove Beam G1 & G2 and Beam A1 & A2 from the top frame and remove all the...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

Do this with the printer shut off.The main objective of the bracket is to keep the weight from the ribbon cable from stressing the connector. It will also help preventing the ribbon cable from dipping down too much.</p><p>Fasten the ribbon cable with...

This is a redesign of markus_p's Mini FPV-Rover, modified to be controlled by a Raspberry Pi Zero W with camera, using the control software created by Wingman94 for it's ZeroBot Pro.Some changes from the original rover:Direct WiFi connection with the...

Heute mal ein Video zum SpeedyBee Master 5 v2 Frame ich hoffe es gefällt euch😊Die verbauten Komponenten findet Ihr hier in der Beschreibung.Teileliste:Frame Kit SpeedyBee Master 5 v2:https://www.speedybee.com/speedybee-master-5-v2-frame/Empfohlener...

Flower PotWhen I’m working on a project, there are times when I need to take my mind off the development and think a little, then I’m distracted by something very simple. Thus, this pot for succulents turned out.</font><br><br></div><div><font...

When there are different screws used, it will be mentioned!&nbsp;1] Hinge assembly:Cut the head of four M4x30 screws off, so that the lentgh of the threaded part is 24mm.[red] Into every hinge-part you have to insert a M4 rod with a length of...

Basic Coefficient = 7.7038 for HTD pulley 3M 16T;and of course a reset (reboot).The controller also remembers the last position before the machine is turned off. This happens every time the Z-axis shafts stop rotating after two and a half seconds. -...

It in the "Off" modes consumes scanty microamps. COB-Led for this lamp is just 3.7V, which does not require an additional booster converter. Don't forget to close jumper "B".</font><br><br></div><div><img...

A forced charging with this diode of a non-rechargeable battery is a fire hazard.We have to cut off the six-pin pinheader because the RTC would otherwise be too tall to fit under the clock face. Remove the battery while doing so to prevent accidental...

And as a feed roller, I used a roller from a Cricket lighter, it fit perfectly in size.The battery charge module can be used from a ready-made charger by cutting off one piece. But at the moment I have created my own modules, which I already actively...

Because its proximity to the COROT-7 star and its high density, it is a candidate for a chthonian planet, an hypothetical kind of planet that is the remnant rocky core of an ice or gas giant which atmosphere was stripped off by the stellar...