oculus quest vive das adapter 3d models

... position for best sturdiness, 50% infill is fine, maybe even less Raft to be recommended, support necessary of course. ... after print, sand down, attach self-adhesive velcro and put a standard face cushion on it, i used one i had from my old vive

this quest 1 grip attatchment was moddled for a driver shaft that was cut from an old driver to a length of 24". The upper part grips the quest controller snug. there is a spot on the lower to put velcro or zip-ties. ...it works well and I hope it is...

Features: * Extremely lightweight * Easy to assemble quickly * Gentle on your straps - these mounting clips are very low-risk in terms of potential damage to the Quest head straps. * Convenient: The arm locks into two rotations - vertical for...

I take no responsibility whatsoever if this printout breaks down during gaming, and destroys your Oculus control or anything else in your home. Read the ReadMe.docx for instructions... ... The clip could be scaled down to around 97% for a tighter...

I didn't want to shell out 40 bucks for the original Oculus bag, because this sturdy box can do the trick just fine and I'm a designer at heart. ...If you've got access to a 3D printer, you don't have to break the bank with a $40 purchase.

I noticed if I cupped my hands around the sides of the quest, you could hear a lot more environmental sounds (fireplace crackling) and it was just a bit louder. I decided to make a 3D printed version of cupping my hands and it seems to work pretty...

... making installation a breeze. A countersink feature for wood screws has also been added for extra stability. To give the stand some personality, an Oculus logo is discreetly embedded into the design, breaking up the plain look of the empty frame.

This clip is similar to what comes with the Oculus Link cable, used to secure the USB cable to the head strap and prevent it from slipping down onto your shoulder. I use the Amazon Basics USB 3.0 3M cable, which fits perfectly snug against the strap....

Wanted something tp snap on the sides of the Quest 2 so that the wires from my in ear headphones were tucked away, but I could still use it either way. I also needed it to pack back in the case. There are two snaps here. One for the thinner arms,...

... ...I was not fond of the required force to clip the originals on. These are easier to put on. I already using it on my quest 2. Print two of them and enjoy. ... 2021-01-13: Added 4mm high with chamfer to remove sharp edge and protect nose :)

I use it together with my cable clip to secure the cable alongside the headband: https://www.thingiverse.com/thing:4625786 and with my Audio Amplifier/Reflector: https://www.thingiverse.com/thing:4631187 Mine roughly doubles the quest battery life...

Just a simple lens cover for the quest 2. Most of the lens cover designs seem to be trying to block off the entire face hole of the headset and have a big block of plastic pushed up against the lenses. For this design I just surround the lenses...

Better Handstraps for the Quest 2 I Printet the little Inserts on my Anycubic Photon Mono in Clear Resin and The Stretcher on my Anycubic I3 Mega in Procatc Signal Red The Stretcher is designed for 20mm Belt, I used a 20mm x 0,5 mm...

I designed my Kinect scanner platform specifically to 3d scan the Quest 2 to make a form fitting cradle that you can conveniently set the headset in vertically and charge. ...Other hardware needed is listed in the hardware list word or text documents.

The Quest Tennis Racket Grip Mod has undergone significant changes to accommodate its new purpose as a high-tech gaming tool. A robust handle has been crafted, and a spacious flat panel has been integrated into the design. This innovative feature...

You will need the Oculus Rift Headphones which you can buy on site likes ebay and such. ... I also used those parts (bought them on amazon.de, but i guess amazon.co.uk is better for everyone ^^) Headphone Cable ...

... You can do PLA but you may need to file down bottom attachment points to make it easily removable. It requires supports and you should decrease layer height at least for the bits that interface with Quest 2 on top and bottom. Category: Gadgets

Have you broken your oculus rift controller guard and need a replacement? We'll look no further! I had the same issue where my controller was cracked, and it did not look good or protected. So, I decided to take it apart and take some measurements. ...

A very quick dirty 3D Scan of the Quest 2 Controller. (Right one) I wanted to do some Wall holders for my controls but I couldn't find any reliable source online for the controls (except paying on CGTrader). So, I decided to use our 3d scanner...

Most other lens covers work well, but they either consume too much space, activate the sensor on the Quest by covering it, or are too small. This design offers a compact way to protect lenses while providing ease of use with magnets for quick putting...

A very quick dirty 3D Scan of the Quest 2 Controller. (Right one)</p> <p>I wanted to do some Wall holders for my controls but I couldn't find any reliable source online for the controls (except paying on CGTrader).</p> <p>So, I decided to use our 3d...

I've created a new version that's more discreet, prints faster and can adapt better to fit snugly around the headband: https://www.thingiverse.com/thing:4062137. A simple cable management system to guide cables towards the back of your head. ... Apply...

- Print: Follow printing settings below (Place flat bottom along build plate!) - Place: Place the wall adapter and the charging cable into their respective positions - Secure: Use a rubber band (or similar securing device) to hold the charging cable...

Clip-on Vive Tracker Mount for the Oculus Quest 2. This can be used to Base Station track your Quest 2. It's great for Mixed VR setups. This version clips onto the groove and strap pivots so that it won't fall off when upside down. Requires 1/4"...

I have a list of the settings for each item I've printed: Item Infill Layer Height (mm) # of Walls Quantity Weight (grams) Supports Time to print (minutes) Rachet Clicker 100% 0.1 Any 1 2 None 17 Rachet Clicker 25% and 100% 0.1 2 1 7 None 72 ...

Inspired by the other DAS adaptors but not a remix. My goal was to make a new version of the adaptor that has minimal support material by eliminating the middle layer. Print it with the flat side down and you should only need support under the very...

https://www.youtube.com/watch?v=q-OyGd2i26g I have cups for the Oculus Rift CV1 Touch Controllers and the Vive controllers (it's the same for both left and right. ... For a full build for the Rift CV1, you will need to print: Right Buttstock.STL Right...

The Vive Lighthouse Adapter is engineered to seamlessly integrate with the Vive Lighthouse ball attachment, effortlessly substituting the traditional wall plate with a secure attachment for a light stand. ...Conceived to be fully 3D printable, this...

... seamlessly integrates with matzman's latest mod to unlock full potential of the map. ... Check out this crucial thread for updates on a critical fix: https://www.reddit.com/r/oculus/comments/7k3heh/need_again_tester_for_a_fix_for_f04s_horrendous/

You can just put your power bank into the mount and mount your battery. The thickness of your battery should be 16 mm. The model is in the best orientation for printing. Don't turn the model in your slicer. I made a hole to hold better. ...You...