oculus quest battery cover 3d models
230915 3d models found related to oculus quest battery cover.prusaprinters
The recesses will hold 4mm*2mm magnets with hopefully enough squeeze space for some superglue. Mirror it for the left battery cover. not sure on the optimal print orientation yet. ...my test prints were in PETG. created from the models provided by...
thingiverse
Mirror it for the left battery cover. not sure on the optimal print orientation yet. my test prints were in PETG. ... created from the models provided by oculus via their touch accessories 2.0 SDK:...
thingiverse
3d print version of the touch 2.0 battery door with a hole in for a magnetic charger, made using the oculus provided models of the controller with top clip added (needs work) and a little place to put magnets
thingiverse
Just the battery cover for the right controller from the oculus quest. This is without the mounting for the magnets and such. ... Downloaded from the oculus developer center.
thingiverse
So I spent 10 minutes in 3D Builder and hacked on the receptacle so the battery stores on the lens cover, now it all fits in the case well. Hope this helps you, too! ... Use with: My battery holder: https://www.thingiverse.com/thing:4711696 These...
prusaprinters
I came up with a battery holder for the Anker PowerCore10000, but getting the whole set up in my case required putting the battery in a bag and letting it ride the lenses. This would not do. So I spent 10 minutes in 3D Builder and hacked on the...
thingiverse
Oculus Quest (1) Battery cover , With option to use lithium battery and Magnetic Cable usb charger. I used 3mm screws instead of magnets cause I didn't have any, but the option is there. Minor adjustments can be made with the screws If you need...
thingiverse
It holds an inexpensive battery pack that I found on amazon that can supply the quest with the necessary 18 Watts of power. The battery pack is a 10,000 mAh battery that costs $18 and linked below. The cable is a 1 foot long USB C cable with right...
thingiverse
•12/31/19 Added reinforced mounting bracket This is a battery holder system that I created for my Oculus quest. It serves to triple battery life with the linked battery bank and as a stable counter weight to the head set. It consists of printed...
thingiverse
Oculus Quest battery / powerbank holder made to be used with the design by makken104 and his design https://www.thingiverse.com/thing:4070533 the holder prints with its own support bit that you can remove when done printing. ... Its made for the ZAGG...
prusaprinters
Oculus Quest battery / powerbank holder made to be used with the design by makken104 on thingiverse and his design https://www.thingiverse.com/thing:4070533 the holder prints with its own support bit that you can remove when done printing. Its made...
thingiverse
Camera cover for the original Oculus Quest, for when not in use, for lens protection, dust cover, and to guarantee privacy from hackers or Facebook. ... Oculus Quest 2 version is at this link: https://www.thingiverse.com/thing:4644108
thingiverse
Here is a 3D scanned replica of the Oculus Quest front cover, inviting you to play freely and explore new dimensions without any boundaries or limitations.
thingiverse
I thoroughly enjoyed playing Portal and Portal 2, so I figured that my Oculus Quest could use a nice cover with the Aperture Logo. Enjoy! ...
thingiverse
I needed an external battery mount with a smaller footprint that would be compatible with any battery pack, so I designed one utilizing command strips to enable quick installation and removal of the battery for effortless recharging. ...The design...
prusaprinters
I wanted a external battery mount that was a smaller footprint and would work with any battery pack, so I made one that uses command strips so you can install and remove the battery for easy charging. It uses a 1ft 90 degree cable for charging and 6...
thingiverse
I utilized a design created by Fangil's Oculus Go as a starting point and tailored it to match the Oculus Quest perfectly. ...My gratitude goes out to Fangil for granting permission to modify their original design.
thingiverse
This is a remix of the Oculus Quest Front Cover And Front Head Strap Attachment. I printed this with the intention of sanding and painting. The v3 model should correct: - The problems related to having the Front Head Strap Attachment disconnect...
myminifactory
I often forget about my Oculus Quest after a marathon gaming session, leaving it exposed on the counter or desk near a window. To avoid the sun ruining my gaming day, I created this protective cover that shields my lenses from dirt and those pesky...
thingiverse
This is my take on a simple lens cover of the Oculus Quest. * v4 works but is a little small * v5 prints now... and makes all the difference with its bigger size * v6 fits perfectly! *Yes, it is supposed to sit well above the lenses!* Note that the...
thingiverse
I wanted to have the bender quest cover, but not have it obscure my camera views, and since the headset already looks like Bender's face, why not remix the cover and just cut Bender's eyes into the cover? Printing this used my whole 220x220 print...
thingiverse
This is my 3d printed battery headstrap for the oculus quest 2. To complete this you need some foam, hot glue and velcro ties. ...This model is only compatible with the anker powercore 10000mah
thingiverse
Component links: Licheers 10000mAh Battery Bank https://www.amazon.de/gp/product/B07KXGXL8C/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 Destek Strap for Oculus Quest 2...
thingiverse
this is a v2 for the battery holder for the oculus quest, the v1 had the holder at the front which made the quest very heavy with a lot of "moment" weight, this new design is nearer to the centre of the headset so there is less moment weight, which...
thingiverse
I used tinker cad to design and This takes me 5 hours to print on a Ender-3 This is meant for oculus quest two here are the straps...
myminifactory
It holds an inexpensive battery pack that I found on amazon that can supply the quest with the necessary 18 Watts of power. The battery pack is a 10,000 mAh battery that costs $18 and linked below. The cable is a 1 foot long USB C cable with right...
thingiverse
These are a heavy-duty battery holders for the Oculus Quest. 1. AUKEY USB C 10K version has battery opening that is 75.5mm x 14.5mm. 2. XT Power 20K version has a battery opening that is 84mm x 22mm with an 11mm radius on the ends. 3. The...
thingiverse
I bought a second Oculus Quest and a second battery, and was surprised that it didn't fit in v2, so I had to widen the space a little bit. ... The battery is the RAVPower Portable Charger 20000mAh PD 3.0 Power Bank QC 3.0 18W USB C External Battery,...
thingiverse
To enjoy longer gaming sessions, add this mount to your Oculus Quest and potentially swap out multiple Anker batteries for continuous play. The recommended Anker battery for this print is available at https://www.amazon.com/gp/product/B005X1Y7I2. It...