oculus quest 2 png 3d models

Quest 2 case with handles. These handles attach to the head band strap so you can carry the whole thing together. Any strap should work. I also added the Oculus logo to the front. See the original by Tukcer to get the lid for this case. ...

**Anker PowerCore+ 10050 battery holder for Oculus Quest 2** Remix of battery holder made by Elizer. https://www.thingiverse.com/thing:4625765 This model is designed for the original head strap. I really liked his design, since it could clip...

So I made one that would be able to be held onto the original strap for the new Oculus Quest 2.  Product:  Anker PowerCore 13000mAh The elastic band can slide into the notches on the holder, and stay in place due to the opposing clip. This makes it...

This is a battery support for Oculus Quest 2 with NEWZEROL head band. The powerbank is a PowerADD Energycell 5000mah but you can use any similar cilindrical powerbank with a diameter of about 27mm.I printed it with Pet-g and 0.8mm nozzle...

Mount a right hand Oculus Quest controller to a Golf club shaft. This requires 4 screws/bolts ~M4 size and 32mm length. I used lock washers and wing nuts with the bolts as well as 2 6.5mm nylon spacers for the middle section of the clamp. The...

This print can be used to attach an [Eafu 6000mAh power bank](https://www.amazon.com/EAFU-Portable-High-Speed-Flashlight-Lightest/dp/B083QK99PZ/) to the stock strap of an Oculus Quest 2 headset to get longer play time. It attaches to the top strap...

I have trouble getting my fingers between the strap on my Oculus Quest 2 and the end of my 90* USBc charging cord, so I made this little slip on that makes it from barely possible to only kinda hard. This was designed to fit the Aceyoon cable, may...

This holds an Anker PowerCore10000 power bank onto the collection of Elite Strap clones here for the Oculus Quest 2. I found other solutions for holding the power bank too hard to use. I didn't have any good rubber bands, and wasn't about to waste...

An adapter to glue a broken old shaft (or a cut new one) and grip together which works in the Golf+ app for the Oculus QUest 2. Two velcro straps of 10 cm are required to mount the controller (left handed or right handed version). Can be...

Remix of Oculus Quest 2 Case to fit MK3 size bed.Controllers now stand vertically. ...Lined the recesses for the controllers with foam to stop them rattling around. Thanks to OP Grafton1046

**This is just a remix of AbeFM - 90* USB-C Charging Cord Pull (Oculus Quest 2) Aceyoon by AbeFM I have chopped the finger grips from the top half of the original design and spun the design around 180 deg and added te grips to the original lower part...

------------------------------------------------------------------------- NOTE: This is for the Oculus Quest 2 controllers. If you are looking for the Quest 1 version, [see here](https://www.thingiverse.com/thing:4759134). WARNING: This is a...

Oculus/ Meta Quest 2 Controller Faceplate ReplacementCustomization in mind! This printable replaces the faceplate on your quest controller (the file included replaces the left plate). THIS WILL VOID THE WARRANTY (probably)This mod requires you to...

This artwork was exported straight from Tilt Brush on my Oculus Quest 2 to Sketchfab without any intermediate steps. Unfortunately, two of the transparent brushes lost their transparency during the export process (I had been warned but forgot to...

A Simple powerbank holder for the oculus quest 2 ^^ (TOPK Power Bank 10000mah) strap diameter for threading is: W: 25,00mm H: 2,50mm i use this one: https://www.amazon.de/gp/product/B08PYVY85Y You need: -TOPK Power Bank 10000mah -Velcro tape 12mm...

Dome adapter for Oculus Quest.

I have remixed Wimi1s Oculus Quest 2 DIY (Elite) Strap V1.0 so that you can print it flat. It reduced the print time for me from about 4h to not much over 1h while using a lot less material for supports - with the aditional benefit of beeing less...

This strap lock works with thatdude902's [knuckle-style TPU strap](https://www.thingiverse.com/thing:4625898) for the Oculus Quest 2 controllers. It enables you to quickly tighten or loosen the knuckle strap, and holds it in place while you're using...

So I made one that would be able to be held onto the original strap for the new Oculus Quest 2. Product:Anker PowerCore 13000mAh The elastic band can slide into the notches on the holder, and stay in place due to the opposing clip. This makes it...

I found no good Oculus Quest 2 Grips for the VRGM VR Stock, so I took two designs I liked and combined em. Grip Source: https://www.thingiverse.com/thing:4248105 Stock Plate Source: https://www.thingiverse.com/thing:4755718 You'll find three...

The 'Oculus Quest 2 Elite Strap_V2_NAVIDA DESIGN' is an excellent upgrade to the stock Quest 2 strap. I've added a flat rectangular shelf to which a small battery pack has been attached (using double sided tape and a Xipin M3 5000mAh pack ). Any flat...

Oculus Quest 2 Prescription Glasses Insert for Family users. My family shares the machine, and everyone wears the prescription glasses. it is economically to use some old glasses lens (as long as it still good with prescription. I used an year...

Summary This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I remix this one for my power bank xiaomi wbp15zm but you can also find more...

This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I made one for my power bank xiaomi 3 but you can also use the generic plate and glue or...

This is a battery mount specifically designed for Oculus Quest 2 Elite Strap. The advantage of our product is listed below: 1. Reduce the distance from the center of gravity of the battery to reduce the centrifugal force generated when turning...

This is a battery mount specifically designed for Oculus Quest 2 Stock Strap. The advantage of our product is listed below: 1. Reduce the distance from the center of gravity of the battery to reduce the centrifugal force generated when turning...

**THIS ADAPTER HAS BEEN SUPERSEDED BY** **https://www.thingiverse.com/thing:5396746** This is a VR table tennis (ping pong) adapter for the Oculus Quest 2 controller designed for Chinese Penhold (CPEN) players in games like Eleven Table Tennis. You...

You may also request this model printed and assembled with velcro and rubber at https://jkl-adapters.com/   Description To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series...

Seen more than a few broken Quest 1 mount plastics (unrepairable) on the Oculus Quest sub reddit. Printed without support and 25% cubic infill for how it looks. [edit] added a version A with wider slots to fit DAS. [edit] Here's a...

This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...