oculus quest 2 mount 3d models

This is a clip for the quest 2 stock head strap that supports your link cable while attached to your headset. ... printable with 0.4mm or 0.6mm nozzle enjoy We have many more great designs on our website, check them out here:...

This is a gun stock i created for the Quest 2. It helps with immersion and also helps with aim a little. I have tried to make the design as simple and user friendly as possible but please note that some sanding will be required (2-3mins per part) as...

Snaps firmly onto the rigid arm of the Elite Strap and holds the Oculus Link cable. ...The Link cable can be removed without removing the clip.</p> <h3>Print instructions</h3><p>Print on one side; brim recommended for improved bed adhesion.</p>

Simple little print I designed to replace the original Quest 2 controller cord cinch which my son broke. Works great! It pressure fit nicely enough for me, but I still glued the outer edges, just in case. I printed it at a 0.15mm resolution...

It appears that this is a large block of text that seems to be a tutorial or guide for creating and using a 3D printed rifle accessory, specifically designed for use with the Oculus Quest VR headset. However, I'll do my best to break it down and...

I decided to try to make locks that would attach to the stock Oculus wrist strap using flexible material. I went through several iterations before I hit on this design that has enough friction to hold onto the string tightly, orient the strap in...

Stock, the Oculus Quest2 does not fit me very well. If I pull the band low enough to keep it from slipping off, there is a huge gap at the bottom of the headset. This print allows me to have a very good fit with no gaps and keeps the headset well...

5 walls, 0.1mm, x2 infill lines, triangles, 20% infill Cut Oculus Strap as close to the old clip as possible. Melt the cut end until there is one solid line of plastic on the end on the strap, for strength reasons. Print the new clips and use the...

Cable clip for your Oculus Link cable, just snaps onto the side of your headset. This helps relieve stress of the very strained and weak USB C connector on your headset. Best printed in ABS or PETG but can be printed in PLA and will probably work...

Print replacement straps for your Oculus elite (with or without battery) strap.&nbsp;There are three versions included:One piece original size (needs bigger print bed)One piece Prusa MK3 bed size (should fit most heads but may be tight if glasses...

Works with the same 5x2mm magnets: https://www.amazon.ca/gp/product/B08H1N2HRJ Zenni Glasses to use: https://ca.zennioptical.com/p/metal-alloy-full-rim-frame-with-spring-hinges/5500?skuId=550021 The other remix increased the height of the parts that...

Link to battery holder V2 with a more secure design and less "moment" weight so it feels lighter than V1: https://www.thingiverse.com/thing:5250979 this is a remix and my first design so that you can have a power bank plugged into the oculus while...

Link to battery holder V2 with a more secure design and less "moment" weight so it feels lighter than V1: https://www.thingiverse.com/thing:5250979this is a remix and my first design so that you can have a power bank plugged into the oculus while...

.2 &nbsp;2 layers concentric infill

After I finished sanding and spray painting this, I connected the triggers and buttons, and used a normal printer to make a BMW logo sticker to put instead of the Oculus logo. You will also have to use a knife to widen the whole at the bottom a...

remix grip from https://www.thingiverse.com/thing:4651978 608 2RS bearing * 2 20mm magnet rubber band M3 bolt nuts

... "Mike vom Mars" https://www.thingiverse.com/thing:4025967 there is a carrier for the glasses and the stand, additional there is a carrier for the Elite battery pack. The controller mountings have been slightly extended to make them easier to use.

... is a Minimal Print. ...intended to save filament Designed for both Headset and Controllers Required materials: 8 screws Notes: -You will need to print of 4 of these, 2 for the headset 1 for each controller -Print on its side to ensure maximum strength

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

As the mount point for headphone element is way more rigid, use hot air gun with small nozzle or jet torch with short bursts until you see first signs of PETG melting, then insert the element. ...Don't push too hard, you will break your element with...

... is a carrier for the glasses and the stand, additional there is a carrier for the Elite battery pack. The controller mountings have been slightly extended to make them easier to use.

As the mount point for headphone element is way more rigid, use hot air gun with small nozzle or jet torch with short bursts until you see first signs of PETG melting, then insert the element. ...Don't push too hard, you will break your element with...

UDATE 2: Re-Meshed the wings “conector” in blender, the V2 was made measuring the physical model, while this V3 is made by using the virtual model, allowing for a perfect fit with the base, they both work equally well, but it might be easier to align...

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

There is a recess within butt to conceal the knot. There is a hole in the butt that will fit a quick release sling swivel. Support free printable parts Print left or right handed controller clamps Print 3 clamp nuts Print one of each of the remaining...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi, but the adapter is movable, so I decided to make it 2mm longer and added a small clip at the end, so it does not get off...

This 3-file OpenSCAD project is a remix of the excellent "Oculus Quest Magnetic Prescription Lens Adapter" project by jegstad: https://www.thingiverse.com/thing:3659124/ Two of the three included files are unmodified from the version V2 of that...

Protective/decorative covers for your Oculus Quest 2 controllers! The holes allow proper tracking of the IR LEDs. Designed to be printed in TPU and slipped directly onto the controller. Three versions: (1) Original - Minimal with small holes. I...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi (https://www.thingiverse.com/thing:4624192), but the adapter is movable, so I decided to make it 2mm longer and added a...

Designed this thing to mount Oculus Quest 2 controllers to a glove, meant for Lucas VR's DIY hand tracking vr gloves.