oculus quest 2 ipd slider stopper by 3d models

This holds an Anker PowerCore10000 power bank onto the collection of Elite Strap clones here for the Oculus Quest 2. I found other solutions for holding the power bank too hard to use. I didn't have any good rubber bands, and wasn't about to waste a...

I took the excellent design by Pledg and re-drew them to fit for my ugreen 90 degree usb-c cable which I use to keep the Oculus charged. ... The clips have slightly more space for the headband and the holder is closer to the headset.

... cable mess. ...Fits on the Elite Strap (with or without battery). Useful for Oculus Link, battery packs, headphones, etc.Inspired by https://www.thingiverse.com/thing:4639044 but remodelled to tweak dimensions and make a clip with two cable slots.

The simple solution is to not use it plugged in, but then the cable hangs down and irritates when you wear the Quest 2. ... So the simple solution is a new cable guard, where the cable is routed better and the last guard doubles as a holder for the...

Original design by 10P6 and I thank you much for that :) I have a Quest 2.... I have a 3d printer.... but its only a 120mmx120mmx120mm build volume, Monoprice Select Mini v2 e3d. i altered the bottom piece on the length only to fit the 120mm. Then...

Clip for Chinostrap Oculus Link Cable Remix of ---> https://www.thingiverse.com/thing:4629345

___ These **magnetic grips** are designed to be used with the 2 x 20 by 3 mm magnets, as I've not had luck with the 4 x 10mm magnets. ___ There's a **cut out for wrist/knuckle straps** on each controller as well. Not only do these help with...

Its just a Remix from this https://www.thingiverse.com/thing:4631187?part=001cc735-c1a3-4abe-9acf-0a9c7e4e7ea0  for the Quest 2 Bobovr M1 Plus Headstrap.

Anker PD 10000 Powerbank holder for Quest 2 elite strap. For counterweight and extended battery life. If there are comfort issues from the mounts please use some padding on the back of the strap Tested on Elite Battery strap. ...But it should work...

Oculus Quest VIVE Audio Headset Adapter

I haven't been able to find a universal battery pack holder for the Ozero Quest 2 elite strap so I decided to draw one up. This is designed to use velcro style cable straps to hold the holder to the head strap and small zip ties to hold the pack to...

This is an easily-printed clip-on battery pack holder for the Quest 2 Elite Strap. Just print, slot the pieces together (perhaps with a little bit of glue), add some foam, and you're good to go. STEP assembly included so you can create your own...

Makes it more convenient and realistic to use a two-handed weapon in VR with the Quest 2. I got tired of my hands constantly moving around whilst sword fighting. I handle swords IRL, and this annoyed me, so I made this. I can't remember where online...

Simple clip for the Quest 2 standard headstraps. Works with the Newzerol and Anker Link cables. New version included for the Original Link cable with a smaller diameter as its cable is thinner. Has a second clip on the outside for...

I wanted to create a Power Bank Clamp system for my Quest 2 BOBOVR M2 Strap to act as a counterbalance for the front heavy VR headset and at the same time utilise the power bank to extend the available playtime. I tweaked the design to achieve both.

Simple clip for the Quest 2 standard headstraps. Works with the Newzerol and Anker Link cables. New version included for the Original Link cable with a smaller diameter as its cable is thinner. Has a second clip on the outside for...

I made the clip extend 1mm farther back since it was too tight of a fit for my oculus. Lastly, the gap for the DAS buckle was made 1mm wider and the location of the strap attachment was angled up and extended back 1cm to make it a little easier to...

I also thickened the pieces attaching the cylinder to the main model by 1mm. I made the clip extend 1mm farther back since it was too tight of a fit for my oculus. Lastly, the gap for the DAS buckle was made 1mm wider and the location of the strap...

It uses headphones from an original Rift CV1, and allows to connect it to the 3.5 mm audio output on the left side of the Quest 2. The electrical contact is managed thanks to salvaged gold-coated contacts found on a female Dean connector,...

Neat gunstock for FPS games on the Oculus 2. After printing three of these for friends I decided to improve a few issues I found and greatly simplify the process for others. Most of the source models have disparate and confusing instructions, so I...

Remixed to properly fit original Oculus link cable. Easier to put on. Sturdier too. ... Thanks to AbeFM https://www.thingiverse.com/thing:4711712/files for original design.

**This is an easily-printed clip-on battery pack holder for the Quest 2 Elite Strap**. Just print, slot the pieces together (perhaps with a little bit of glue), add some foam, and you're good to go. **STEP assembly included so you can create your...

Was gonna grab some of the Sony ZX110 headphones for my Quest 2 and realized i had an old pair of Skull Candy over ear headphones that I remember rivaling my $200 bose set. So I remixed SolidRye's mount to use the cut up skull candy units. Give a...

This is a remix of hadtstec's rift headphone adapters from here: https://www.thingiverse.com/thing:3652427 This has been modded to fit securely on the Quest 2 since it uses a totally different strap design. These headphones are great if you're...

The battery I recommend is the $20 10,000mah Aukey with passthrough charging that has USB-C on one side and USB-A on the other, so that you never need to unplug the battery from the Quest 2, but for some reason it's not always available:...

I decided to mod my (dead) CV1 head strap with audio and use it with Quest 2 which has pretty mediocre build-in  sound system. My model uses interface provided by tanvach here: https://www.thingiverse.com/thing:4626664You will need to...

A little adapter to use my previous koss porta pro adapters with the quest 2 elite strap. Used tinkercad to edit the models remix of the following https://www.thingiverse.com/thing:4623948 Great little clip, might be a little tight (didn't modify...

A little adapter to use my previous koss porta pro adapters with the quest 2 elite strap. Used tinkercad to edit the models remix of the following (Can't seem to add as remix(thingiverse please)) https://www.thingiverse.com/thing:4623948...

Camera cover for the original Oculus Quest, for when not in use, for lens protection, dust cover, and to guarantee privacy from hackers or Facebook. ... Oculus Quest 2 version is at this link: https://www.thingiverse.com/thing:4644108

Custom-designed steering wheel originally created for VR Škoda Time Machine experience available for Oculus Quest here. ... This steering wheel is designed for Oculus Quest controllers and by mounting them on it mimics an actual steering wheel.