oculus quest 2 golf club attachment 3d models

This extension allows to attach your Quest 2 controllers to a real golf shaft. Get you hands on some old putter or other club and cut the shaft in half. Now you can fasten the printed part to the shaft with 2 nuts and bolts. Alternatively you could...

I cut 30mm from the rubber handle on the club and attached in to the printed part, that should leave 3-4mm between rubber handle and the printed part. Drilling holes in each side of the gold club tube for the bolt was not easy. I had a hard time,...

An adapter to glue a broken old shaft (or a cut new one) and grip together which works in the Golf+ app for the Oculus QUest 2. Two velcro straps of 10 cm are required to mount the controller (left handed or right handed version). Can be...

Mount a right hand Oculus Quest controller to a Golf club shaft. This requires 4 screws/bolts ~M4 size and 32mm length. I used lock washers and wing nuts with the bolts as well as 2 6.5mm nylon spacers for the middle section of the clamp. The...

This is my version of a golf attatchment made specifically for my Oculus Quest 2! I tried to make the design as similar to Deadeye VR's product as possible. So instead of spending $70 I only spent $10! The controller should fit inside the print very...

I wanted to use the head strap of Quest3 with Quest2, so I made it.Please be sure to read the notes below and use at your own risk.When attaching and detaching parts, there is a possibility of damaging the VR device itself.Depending on the strength...

Please be sure to read the notes below and use at your own risk.When attaching and detaching parts, there is a possibility of damaging the VR device itself.Depending on the strength of the parts, they may break during play, causing injury or...

... belt strap to secure your controller. ...You can get them here: https://sanlaki.shop/products/golf-club-diy-kit Walkabout Minigolf - set angle to 38Golf+ - use Sanlaki preset (currently broken, working with devs to get the alignment sorted out)

4894874/5411253To assembly you need 2 M3 Bolts & screws, im using 20mm.The hole in the club is 3.5mmPrinted in TPUNot tested in PLA ( I think it would not work because the hole where you put the controller works with friction )For the infill, i have...

I found the best success with the "CUSTOM" club in the golf+ settings and aligning the remote onscreen with the actual location of the remote on the golf club handle in real life. The dead eye works but custom seems better. The picture shows using...

It's designed to handle an Oculus Touch controller into a shaft of a real golf club to be used in __a game who allow to use theses__ specific controllers (Golf Club VR). Depending of the print and printer quality, it no need to print supports. ...

This is a remix of https://www.thingiverse.com/thing:5204772. ... I needed to make it a bit stronger as it broke off at one point. There are also 2 different versions, 13.5 and 14.5 shaft diameter.

This model is designed to securely mount a quest 3 (Right) controller to a golf club putter. I made this to use with ‘Walkabout mini-golf’. You can calibrate it in game by going to options, clicking on custom-grip and using the grab button to...

No Supports needed to print this model. ... This rake can be attached to your bag for easy access, it attaches to your golf club to easily rake the bunkers. ... By having your own rake we can reduce the spread of COVID.

This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...

This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...

We designed this rake attachment to try and prevent the spread of COVID at golf courses. ...Please go follow us on: Facebook: https://www.facebook.com/Riggers3D/ Instagram: https://www.instagram.com/3d_riggers/ LinkedIn:...

This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I made one for my power bank xiaomi 3 but you can also use the generic plate and glue or...

Summary This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I remix this one for my power bank xiaomi wbp15zm but you can also find more...

This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I made one for my power bank xiaomi 3 but you can also use the generic plate and glue or...

The battery I recommend is the $20 10,000mah Aukey with passthrough charging that has USB-C on one side and USB-A on the other, so that you never need to unplug the battery from the Quest 2, but for some reason it's not always available:...

this quest 1 grip attatchment was moddled for a driver shaft that was cut from an old driver to a length of 24". The upper part grips the quest controller snug. there is a spot on the lower to put velcro or zip-ties. ...it works well and I hope it is...

Wall mountable Oculus Quest 2 holder for headset & hand controllers with base and raised Oculus logo.

this is a remix from 2 people i sew, and i just orderd my oculus quest 2 so i want a docking station, you need support the controllers stand and for the controller stand attach with the oculus stand. there is the final result give like and follow to...

Oculus Quest 2 compact stand, no glue or screws required. You can add foam padding at the top, so the headset lays on a soft surface. Update 2023/01/22: Finally updated for the new Meta logo ! Added 5 files: To keep the old stand with the Oculus...

This is a clean version of the developer released 3d files from oculus for the quest 2 controllers. Scaled to in in-person measurements. Hopefully people can use this to make some cool oculus accessories. ...Please let me know if you have any issues.

Couldn't find a dock for the Oculus Quest 2 that I liked, so I made my own! Design goals: Easy to print with no supports needed Small footprint Protects Quest 2 lenses by completely covering them If anyone has design ideas to also mount the...

Couldn't find a dock for the Oculus Quest 2 that I liked, so I made my own! Design goals: - Easy to print with no supports needed - Small footprint - Protects Quest 2 lenses by completely covering them If anyone has design ideas to also mount the...

I was inspired by this PSVR stand: https://downloadfree3d.com/3d-printing-models/gadgets/playstation-vr-psvr-stand/and I decide to make my own model for oculus quest 2 from scratch.every file ends with B is for black and W is for white - but you...

Here is a rewritten version of the original text: "I'm offering a high-quality 3D model of Oculus Quest 2 controllers, featuring excellent topology and detailed textures. The file format is FBX, which includes four high-resolution PNG files: base...