oculus quest 2 golf accessories 3d models

This is my version of a golf attatchment made specifically for my Oculus Quest 2! I tried to make the design as similar to Deadeye VR's product as possible. So instead of spending $70 I only spent $10! The controller should fit inside the print very...

This extension allows to attach your Quest 2 controllers to a real golf shaft. Get you hands on some old putter or other club and cut the shaft in half. Now you can fasten the printed part to the shaft with 2 nuts and bolts. Alternatively you could...

"Quest_Golf_Adapter_JSD_v2.stl" Is the same as above, you can see I change it up some. Either one works fine, not sure one is really better than the other. V2 has more plastic so may be a bit stronger, but weigh more. Used M3x40mm bolts because...

An adapter to glue a broken old shaft (or a cut new one) and grip together which works in the Golf+ app for the Oculus QUest 2. Two velcro straps of 10 cm are required to mount the controller (left handed or right handed version). Can be...

Quest 2 Golf+ adapter. Just add 1 or 2 velcro straps. I found the best success with the "CUSTOM" club in the golf+ settings and aligning the remote onscreen with the actual location of the remote on the golf club handle in real life. The dead eye...

This is a remix of https://www.thingiverse.com/thing:5204772. ... I needed to make it a bit stronger as it broke off at one point. There are also 2 different versions, 13.5 and 14.5 shaft diameter.

Mount a right hand Oculus Quest controller to a Golf club shaft. This requires 4 screws/bolts ~M4 size and 32mm length. I used lock washers and wing nuts with the bolts as well as 2 6.5mm nylon spacers for the middle section of the clamp. The...

This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...

This mount was specifically designed for use with Walkabout Mini Golf on the Oculus Quest 2, and is intended to (more or less) map the angle of the physical putter to the in-game virtual putter. As such, it might not map as well to clubs in other...

this quest 1 grip attatchment was moddled for a driver shaft that was cut from an old driver to a length of 24". The upper part grips the quest controller snug. there is a spot on the lower to put velcro or zip-ties. ...it works well and I hope it is...

Wall mountable Oculus Quest 2 holder for headset & hand controllers with base and raised Oculus logo.

This is a clean version of the developer released 3d files from oculus for the quest 2 controllers. Scaled to in in-person measurements. Hopefully people can use this to make some cool oculus accessories. ...Please let me know if you have any issues.

this is a remix from 2 people i sew, and i just orderd my oculus quest 2 so i want a docking station, you need support the controllers stand and for the controller stand attach with the oculus stand. there is the final result give like and follow to...

Oculus Quest 2 compact stand, no glue or screws required. You can add foam padding at the top, so the headset lays on a soft surface. Update 2023/01/22: Finally updated for the new Meta logo ! Added 5 files: To keep the old stand with the Oculus...

Couldn't find a dock for the Oculus Quest 2 that I liked, so I made my own! Design goals: Easy to print with no supports needed Small footprint Protects Quest 2 lenses by completely covering them If anyone has design ideas to also mount the...

Couldn't find a dock for the Oculus Quest 2 that I liked, so I made my own! Design goals: - Easy to print with no supports needed - Small footprint - Protects Quest 2 lenses by completely covering them If anyone has design ideas to also mount the...

3D model of Oculus quest 2 controllers , with good topology and already textured. ...Format： FBX Textures (4k PNG files, 4096*4096 ) include: base color , roughness and normal map Polygon count: 57978 UV mapped Feel free to contact me if you have any...

3D model of Oculus quest 2 , with good topology and already textured. ...Format： FBX Textures (4k PNG files, 4096*4096 ) include: base color , roughness, Emission and normal map Polygon count: 44897 UV mapped Feel free to contact me if you have any...

Simple hanger I made for my Oculus Quest. Looks good while keeping short print times, took about 2.5 hours for me. The pieces can be used for either side, so print two of each to hang the headset. I would use supports but forgot to turn it on in...

This is an Oculus Quest 2 dock for the headset and its two controllers. There is also a notch for the charging port to sit in while the headset is fully charged. I printed out a prototype and added in extra notches for the controller index finger...

A pistol to go with the grips I've previously posted for the Oculus Quest 2 controllers: https://www.thingiverse.com/thing:4760656 The pistol is in 2 parts that clamp to the controller ring. Secured either with M4 12mm countersunk Allen head bolts...

I was inspired by this PSVR stand: https://downloadfree3d.com/3d-printing-models/gadgets/playstation-vr-psvr-stand/and I decide to make my own model for oculus quest 2 from scratch.every file ends with B is for black and W is for white - but you...

Beautiful stand with the Metaverse logo for your Quest 2 Protect them from any liquid spills with this elevated stand. Plus give your device a great view. ... Simple printing without stands

This is the second generation headset for oculus with the left and right controllers.

This is the second generation headset for oculus with the left and right controllers.

Hi, this is a remix of 2 different Thingis optimized for me and my Quest 2. You can also change the position of the shoulder rest, for the 2nd controller just mirror the "holder" and print it again, if you choose the widest possible position for the...

I designed this set of eyeballs using Fusion 360 to give the Oculus headset a bit of style. I printed them face down on the buildplate using supports and two pauses for color changes. ...They just slide on from the side.&nbsp;</p>

Created by combining Yanev's parametric case, with a 3d scan of the packaging that the quest came in.It's not a small model, you'll need a &gt;300 mm bed to fit it.&nbsp;

... up a little so that the unit has a bit of a backstop. Like the original, it prints well without supports. I used the Filament Fridays Extra Fast .28 Cura profile for speed, but the fine detail was a bit rough, so I will probably reprint at .2.

Oculus quest 2, quest link cable clip