oculus quest 2 elite strap counterweight 3d models

Just add 1 or 2 velcro straps. I found the best success with the "CUSTOM" club in the golf+ settings and aligning the remote onscreen with the actual location of the remote on the golf club handle in real life. The dead eye works but custom seems...

Magnetic Gunstock for Oculus Quest 2 (Improved & Simplified)After printing three of these for friends I decided to improve a few issues I found and greatly simplify the process for others. Most of the source models have disparate and confusing...

... Mark the top of the lens before removing it from the frame. ...If necessary, secure with instant adhesive against rotation. The glasses should be ordered with 65mm IPD for quest 2. ...

Its just a Remix from this https://www.thingiverse.com/thing:4631187?part=001cc735-c1a3-4abe-9acf-0a9c7e4e7ea0  for the Quest 2 Bobovr M1 Plus Headstrap.

Oculus Quest VIVE Audio Headset Adapter

Makes it more convenient and realistic to use a two-handed weapon in VR with the Quest 2. I got tired of my hands constantly moving around whilst sword fighting. I handle swords IRL, and this annoyed me, so I made this. I can't remember where online...

Simple clip for the Quest 2 standard headstraps. Works with the Newzerol and Anker Link cables. New version included for the Original Link cable with a smaller diameter as its cable is thinner. Has a second clip on the outside for...

Simple clip for the Quest 2 standard headstraps. Works with the Newzerol and Anker Link cables. New version included for the Original Link cable with a smaller diameter as its cable is thinner. Has a second clip on the outside for...

Works seamlessly with Quest 2 Elite Headstrap and Quest 1 stock headstrap. Employs the Anker PowerCore 10000 Portable Charger, available at the link below, to significantly extend the Quest's battery life. Combined a clip and casing from another...

Remixed to properly fit original Oculus link cable. Easier to put on. Sturdier too. ... Thanks to AbeFM https://www.thingiverse.com/thing:4711712/files for original design.

Remix of the [Quest 2 wall mount made by lensfort](https://www.thingiverse.com/thing:4630669). I noticed that the HMD mount started to sag over time, so I chose to add some support beams to it and decided that I might as well upload it here. If you...

Hope this helps you, too! Use with: My battery holder: https://www.thingiverse.com/thing:4711696 These "elite" straps: www.thingiverse.com/thing:4636924 www.thingiverse.com/thing:4629958 www.thingiverse.com/thing:4635406 Print Settings Printer Brand:...

Original design by 10P6 and I thank you much for that :) I have a Quest 2.... I have a 3d printer.... but its only a 120mmx120mmx120mm build volume, Monoprice Select Mini v2 e3d. i altered the bottom piece on the length only to fit the 120mm. Then...

Camera cover for the original Oculus Quest, for when not in use, for lens protection, dust cover, and to guarantee privacy from hackers or Facebook. ... Oculus Quest 2 version is at this link: https://www.thingiverse.com/thing:4644108

A modification of the great oculus wall mount by lensfort and ekurutepe by modifying the mount to fit on my side panel of my desk. Panel is 25.96mm and the mount of the STL is 26.05mm. ...It fit perfectly.

I took the excellent design by Pledg and re-drew them to fit for my ugreen 90 degree usb-c cable which I use to keep the Oculus charged. ... The clips have slightly more space for the headband and the holder is closer to the headset.

It uses headphones from an original Rift CV1, and allows to connect it to the 3.5 mm audio output on the left side of the Quest 2. The electrical contact is managed thanks to salvaged gold-coated contacts found on a female Dean connector,...

I find a lot better and comforting in my VR sessions the one with the clip and to always have the battery as it helps a lot with the counterweight. I have tested to move my head like crazy and never had any issue. ...Actually, improved my head...

Neat gunstock for FPS games on the Oculus 2. After printing three of these for friends I decided to improve a few issues I found and greatly simplify the process for others. Most of the source models have disparate and confusing instructions, so I...

Sanlaki's Quest 2 VR non-dominant controller mount gave me a lot of wrist problems and that's likely because the non-dominant hand is mounted like the dominant hand as if there are two pistol grips but a foregrip or a handguard position is nothing at...

Mark o.o1 is 80% sword 20% gun, weight adding supported Mark 1 is sword&gun 50% each, weight adding not supported choose whichever you like Required screws and magnet: 4x M4 x 20mm [ or ] 2x M4 x 40mm + 2x Nuts four 30mm x 5mm magnet (or anything...

XaviXV was on track but did not have a controller mount for the Quest 2. Credit to tigerflip for designing the controller portion of the grips as I could not have made this without that. This remix is an angled magnetic connection making it easier to...

This is a controller arm for the amazing mech VR game "Iron Rebellion" For assembly you'll need two rods of 16mm in diameter and about 360mm in length, one rod of 16mm in diameter and 80mm in lenght, six bolt of 5mm in diameter and 20mm in leght and...

I did use another print but as soon I replace the stock oculus headstrap that print became almost useless. So I made this mod based on Spatz0r thing. The idea was get the best audio possible w/o block the ears or add more heating to my head. As...

2 arruelas magnéticas de 32 mm 2, https: //www.amazon.com / - / es / Di ...

This is a remix of https://www.thingiverse.com/thing:5204772. ... I needed to make it a bit stronger as it broke off at one point. There are also 2 different versions, 13.5 and 14.5 shaft diameter.

https://www.obi.at/temperguss-fittings/fitting-21-mm-r-1-2-x-200-mm-temperguss/p/2297968 I used those 2 magnets https://www.supermagnete.at/topfmagnete-mit-bohrung-und-senkung/topfmagnet-mit-senkbohrung-32mm_CSN-32...

(Please note, the cover used in the image has not been sanded/painted) 3D PRINTING SETTINGS Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 25% Filament: PLA Blackoculusfrontcovervenomquest22questquest...

... like I did for my skullcandy headphone mounts. ... Intended to use Qty 2 #10 wood screws to go into studs on wall. ... V6 is a thicker piece that is much sturdier and has underside chamfers to make it easier to remove the headset from the hanger.

This is the version that it works with ; https://www.thingiverse.com/thing:5146370 Its a fun small print to connect 2 sabers and make one 2 bladed saber. I used to default holes in the bottom of the saber handle design. If you printed that...