oculus quest 2 counterweight 3d models

remix grip from https://www.thingiverse.com/thing:4651978 608 2RS bearing * 2 20mm magnet rubber band M3 bolt nuts

This model requires a 1.5m hook-and-loop fastener. ... You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. ... The battery must be mounted upwards.

Its a remix only bc I added 2 screw holes to the headset part, other than that credit goes to the OP. Thanks Headset didnt need support but the controllers did. I used tree, everywhere. ...

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

... is a Minimal Print. ...intended to save filament Designed for both Headset and Controllers Required materials: 8 screws Notes: -You will need to print of 4 of these, 2 for the headset 1 for each controller -Print on its side to ensure maximum strength

UDATE 2: Re-Meshed the wings “conector” in blender, the V2 was made measuring the physical model, while this V3 is made by using the virtual model, allowing for a perfect fit with the base, they both work equally well, but it might be easier to align...

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

There are 2 versions of this, one with AND one without secure tabs. Designed in Fusion and printed with Windows Print 3d using ABS. The rims for both are beveled. 1. Without Tabs - Just press the O into the rim. The rim is beveled and is...

There is a recess within butt to conceal the knot. There is a hole in the butt that will fit a quick release sling swivel. Support free printable parts Print left or right handed controller clamps Print 3 clamp nuts Print one of each of the remaining...

It appears that this is a large block of text that seems to be a tutorial or guide for creating and using a 3D printed rifle accessory, specifically designed for use with the Oculus Quest VR headset. However, I'll do my best to break it down and...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi, but the adapter is movable, so I decided to make it 2mm longer and added a small clip at the end, so it does not get off...

This 3-file OpenSCAD project is a remix of the excellent "Oculus Quest Magnetic Prescription Lens Adapter" project by jegstad: https://www.thingiverse.com/thing:3659124/ Two of the three included files are unmodified from the version V2 of that...

Protective/decorative covers for your Oculus Quest 2 controllers! The holes allow proper tracking of the IR LEDs. Designed to be printed in TPU and slipped directly onto the controller. Three versions: (1) Original - Minimal with small holes. I...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi (https://www.thingiverse.com/thing:4624192), but the adapter is movable, so I decided to make it 2mm longer and added a...

Just my design of a Anker Powercore 2 10 000mah holder for Oculus Quest 2 (for elite and basic strap) The locking of the battery is done with a cable tie

https://youtu.be/3c4S7vyELSE for oculus quest 2

This is a quick IPD checker I made for the Oculus Quest 2. Very handy for when you want people to try out VR without needing a ruler to check their IPD The way to use it is by lining up the left point with one eye, and seeing which point their other...

Two-Handed Sword Adapter for Oculus Quest 2. ...Feel free to remix and improve

Oculus Quest 2 Strap mount with battery v2 PLA or PETG

So I made one that would be able to be held onto the original strap for the new Oculus Quest 2. Product: Anker PowerCore 13000mAh The elastic band can slide into the notches on the holder, and stay in place due to the opposing clip. ...This makes it...

Holder for Oculus Quest 2 controller holder and plate to stick it to the back of your hand.

This is kind of a remake from https://www.thingiverse.com/thing:4761076 because the controller hooks failed to print.. So I remade the platform with stronger and printable hooks(supports still needed) I have included the platform in SKP (Sketchup)...

10 clips instead of 4

Estuve trabajando en un Gunstock ( https://www.thingiverse.com/thing:5496577 ) y me di cuenta que el Grip era muy muy cómodo. Tanto que podría servir para hacer una pareja de fundas con strap para todo tipo de juegos. y aquí esta! Se...

i designed this to improve my accuracy in shooting games

So I made one that would be able to be held onto the original strap for the new Oculus Quest 2.  Product:  Anker PowerCore 13000mAh The elastic band can slide into the notches on the holder, and stay in place due to the opposing clip. This makes it...

... your head. ... extends the Quest 2 to at least 6 hours of play time when both the internal battery and Anker are full Anker Astro E1 - https://amzn.to/3kxztsU Short USB A- to C cable 12" https://amzn.to/2ZU8JZS Oculus Quest 2 - https://amzn.to/3bAABb2

This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I made one for my power bank xiaomi 3 but you can also use the generic plate and glue or...

Summary This thing is to attach your power bank to the back of your oculus quest head strap. I can recommend this not just for charging, but also for counterweight. I remix this one for my power bank xiaomi wbp15zm but you can also find more...

This is a Cabel clip for the Oculus Quest 2 Elite strap fitted for 4 mm cabels like the Original Oculus Quest 1 Charging cabel ( the Quest 2 charging cabel fits, too just a bit more loose ) *** EDIT *** I noticed that i uploaded the wrong model ... ...i...