octoprint psu control ender 3 3d models

A set of brackets to move PSU from the side to the rear of Ender 3. **Does not fit Pro or V2**. UPDATES: 1. Alternative version **2.0** to be mounted with M5 bolts screwed into tapped holes in openings of profiles. Check if you have those holes...

I designed the bracket so the original screws from the Ender 3 fit. To screw it to the table I used 3,5mmx20mm wood screws I had on hand. If you want to do it like me just print the switch side bracket from dade75...

Does NOT fit Ender 3 Pro with the slim PSU, this is for the standard Ender PSU that is 50mm wide. I liked the design from Zoly, BUT I wanted to make some changes. For the "rear_left" I added some loops inside for zipties and filled 2 holes (since...

Simple brackets to mount your Ender 3's power supply elsewhere using OEM bolt holes on the PSU. Uses the same size bolts already used on the PSU's plastic cover. (Believe they're M4) I'm using it to mount under the shelf the printer sits on to clear...

I copied the original ender 3 style by making the case to mount on the back right rail where the old ender 3 psu was at. My setup uses 2 5v fans (4010 and 3010), 3 buck converters LM2596 DC-DC (standoffs printed on design, a rpi 3 B+ but a rpi 4...

Alternative PSU Mount for the belt3dprinter.com Ender 3 Belt printer kit. On the beta version of the kit one hole for the stock PSU mounting location was drilled wrong. So in order to get on with testing I designed this right quick and now that I...

...Alternatively, you can just print the rear bracket as it is sturdy enough to hold the entire PSU, but using both will add extra support. These are compatible with my Scuddy Dual Z Upgrade for the Ender 3 at: https://www.thingiverse.com/thing:3451260

Ender 3 PSU Fan Duct/Silencer. This fan duct/silencer features smooth surfaces that require precise gluing techniques since they lack any studs, making it crucial to achieve a nearly invisible bond between the parts. ...A solid version of this model is...

I loved the initial concept by dade75 (https://www.thingiverse.com/thing:3747148) but discovered the hard truth - the Ender 3 Pro ships with a unique PSU that refused to fit. ...I crafted this custom mount, drawing inspiration from his original design...

I designed a Creality Ender 3 PSU fan shroud to alleviate the maddening noise that was driving me nuts. I decided to see if I could significantly minimize it. I utilized four 2x1mm magnets to enable spinning the shroud into position, which would...

A PSU mount for the Ender 3 to make room for a 2nd Z-Axis stepper. Uses the existing bolt holes in the side of the plastic housing. Uses 4, ~12mm M4 bolts and washers. ... You will need to have a grounding wire connecting the printers frame to the power...

I made this model to replace my original Ender 3 PSU to the back of the printer, below the Y axis. Since the PSU is taller than the space below the axis, I also printed some feet for the printer. To attach the model to the PSU you'll need 5 M4...

I designed a box to add new features to my Ender 3 like: - Have remote control of the printer from your smartphone (Printoid) - Turn your printer on or off - Turn the light on or off, useful when a camera is installed see link below to understand and...

Please note that this design is specifically tailored for the base model Ender 3 PSU. However, I am unsure if it will fit the higher spec (Ender 3 Pro) PSU. This cover was printed using a 0.2mm layer height and with a brim. ...If you have confidence...

This installation is controlled using an OctoPrint plugin available at https://github.com/damienmg/OctoPrint-ControlBox.CoolingCooling is done with http://www.thingiverse.com/thing:3576392.Print SettingsPrinter Brand:Creality Printer: Ender...

I wanted my PSU to be under the rear side of the bed like the Ender 3 v2 is, but looking at the existing mounts, they were either mounted so the fans were facing up or had no access to wiring and a tighter fit than I wanted. I designed this setup...

This print will allow for the PSU beneath the Ender 3 V2 to actually breathe. As stated in the Meanwell documentation sheet, the holes on the PSU are not to be covered by any means. So this print will do a great job of organizing the PCB wires and...

To relocate the PSU on my Ender-3, I required an expedient model of the PSU itself. The outside dimensions must be precise, and since I'm likely to mount it upside-down from the Y-axis rail, the hole pattern on the bottom is accurate as well. I also...

# Additional Hardware * 1x M3 bolt at least 6mm long for holding the two pieces together * 4x M3 bolts that are 4mm long to mount the relay board * Stock mounting bolts/screws for the power connector and power supply # Additional Notes Apparently,...

This is a mount for the ender 3 pro PSU when re located for an enclosure. I was building a enclosure for my ender 3 pro and wanted the psi to mount the back leg of the table. I couldn't find anything that would work for what I need so I made this. ...

Replacement Ender 3 Pro PSU cover, with 2mm smaller depth for a better fit with https://www.thingiverse.com/thing:4669624 - you also don't need to print the cover for the opening of the old plug with switch as this hole (and the pill shaped hole from...

This is for non-Pro Ender 3

I needed to add dual x axis to my Ender 3, but relocating the PSU was required. The only spot I could put it was on the back on a shelf, however, the power switch wouldn't fit so a switch box had to be made. This box has two holes in the top for...

Lightweight PSU silencer for Ender 3 (& possibly other Creality) printers. Fits for fans with diagonal distance between screws of 71,5 mm. All walls have just 1,2 mm. Additionally the outlet channels are wavy reducing noise even more. Print flat,...

Lightweight PSU silencer for Ender 3 (& possibly other Creality) printers.\ Fits for fans with diagonal distance between screws of 71,5 mm.\ All walls have just 1,2 mm. Additionally the outlet channels are wavy reducing noise even more. Print flat,...

This model enables you to relocate your PSU on an Ender 3 Pro, making it easier to install a second Z lead screw and motor. Alternatively, you can use it to remove excess weight from your uprights. It optimizes air flow to keep the PSU cool. The...

This mount is for the original Ender 3 with the fat PSU (mine's model number is Cheng Liang P360W24V). The original design had misaligned screw holes on one side, and not enough clearance above the terminals to fit the PSU in all the way. I've...

Air duct cover for Ender 3 PSU (or any compatible power supply) primarily designed for noise reduction. It directs the air coming out of the supply towards the back of the printer. Mounted using double-sided foam tape. Print vertically with brim...

ORGINAL MAKE: JanWillem Drenten Link: https://grabcad.com/library/ender-3-pro-psu-cap-with-70mm-fan-1 I used PLA because I'm low on PETG But i highly recommend using PETG as it will be more temperature resistant. ... I used their file for all the...

This installation is controlled using an OctoPrint plugin available at https://github.com/damienmg/OctoPrint-ControlBox. **Cooling** Cooling is achieved with a design found on http://www.thingiverse.com/thing:3576392. **My TODO List** - Complete...