octoprint light control 3d models

The goal was to keep the overall design as straightforward and uncomplicated as possible while incorporating a unique feature - remote LED light control via OctoPrint. To achieve this, I utilized the System Command Editor plugin for OctoPrint in...

* Outputs control devices (temperature, lights, fans, etc.) and can be set to various types (GPIO, PWM GPIO, Neopixel Control, Temperature Alarm, GCode Output). * Inputs trigger actions or input values to the plugin (temperature sensor, GPIO...

I used the custom control plugin for octoprint to make a quick access on/off button (https://plugins.octoprint.org/plugins/customControl/) G-code Terminal Commands: (On - M42P69S255) & (Off - M42P69S0) Supplies you will need: LED light strip i used...

To power/control the light, use custom control plugin for octoprint which provides quick access to on/off button. G-code Terminal Commands are as follows: On - M42P69S255 & Off - M42P69S0. The following supplies are needed: * LED light strip...

Ender 3 Power and Light Controls Managed via Octoprint Interface USB Power Disabled by Default Instructions Apply to the 5V LED Version Only Utilizing Raspberry Pi v3 All Necessary Components, Including Configuration and Wiring Instructions, Can Be...

But to accomplish power switching for the printer and lights you only really need two relays, and one fan should be sufficient for cooling. To make everything fit some tricky positioning had to be done. The Pi now sits on a raised bracket to provide...

But to accomplish power switching for the printer and lights, you only really need two relays, and one fan should be sufficient for cooling. To make everything fit some tricky positioning had to be done. The Pi now sits on a raised bracket to...

... * Configure OctoPrint UI to access relay controls using the following code: ```yaml system: actions: - action: pon command: printer_on.sh name: PrinterOn - action: poff command: printer_off.sh confirm: Are you sure you want to turn off the printer?

Two relays are sufficient, one for power and another for 24V LED lights. ...The original design featured a relay for both power and ground; I simply blocked the 5-volt pin on the USB cable connected to the RPI board, preventing it from drawing power...

The rear IO on a Raspberry Pi 3 gets turned upside down when compared to a Raspberry Pi 4. ...This redesign relocates the Ethernet jack and collection of USB connectors to suit the needs of a Raspberry Pi 4.

Control-Box für Octoprint Die Anleitung habe ich von: https://plugins.octoprint.org/plugins/display_panel/?utm_medium=announcements&utm_source=octoprint&utm_content=1.5.2

Additional housing based on the great Octoprint Control Panel design (https://plugins.octoprint.org/plugins/display_panel/?utm_source=octoprint&utm_medium=announcements&utm_content=1.5.2). ... I adapted it with my Raspberry 3 Housing:...

This pairs with an OctoPrint plugin, [available on my Github](https://github.com/sethvoltz/OctoPrint-DisplayPanel) **Check out a demo here** [](https://youtu.be/78emT1ollu4...

To set up your hardware, install three additional plugins from the OctoPrint Repository: OctoPrint-Enclosure, PSU Controls, and System Command Editor. Safety Alert: This build involves mains voltage, which is hazardous and potentially lethal. I am...

Those are cool looking and I love the ESP line of chips, but I really wanted something directly connected so it could get immediate events and feedback, as well as act as a pause and cancel control. This pairs with an OctoPrint plugin, available on...

You can of course use any other GPIO pins, that's up to you. Software setupThe configuration for the three OctoPrint plugins are shown below (OctoPrint-Eclosure, PSU Control and System Command Editor). As it turns out the GPIO nunbering scheme set in...

I WILL APPRECIATE YOUR CONSTRUCTIVE CRITICISM I wanted to easily control some functions on my CR10s particularly since I put it inside an enclosure. However, all the designs I found on Thingiverse use the 6x6 tactile push buttons. I wanted to use the...

Some of the key points from the tutorial include: * Creating custom scripts to automate tasks such as turning off the printer and light when the print is completed or failed * Setting up automatic running of the scripts at startup and during...

Here is the link to the wiring diagram: https://i.imgur.com/pYo7L1e.png That being said, I made this box to control power and LED lights on both printers through GPIO pins of the Raspberry Pi within OctoPrint. The box is designed to hold a...

Raspbery Pi 3** or better Octropi image for the Raspberry Pi Some MOSFET modules to control lights and power relay I recommend a 64GB SD card for use with timelapse Raspberry Pi Camera, Wide angle helps here! Long cable for camera A 5v power supply,...

Here is a compact OctoPrint Control Box which inspired by [OctoPrint Control Box](https://www.thingiverse.com/thing:3219619). Required parts are: * Raspberry Pi 3 * Fotek 220v SSR * 5v 4010 Fan * 12mm Push Button * 5v 5A smps in 87*58*35mm...

Introduction I have a Wanhao Duplicator i3, a raspberry pi 2 running octoprint (the octopi image), an LED light above the printer, and a 4 relay board from sainsmart. There are places with instructions, tips, etc. But I wanted to share how I did it...

Another Control Box for OctoPrint. Materials List: - 5V Power Supply (MeanWell, RS-15-5) - 5V Relay (Keyes-019) - IEC 320 C13 and C14 with Fuse (https://www.aliexpress.com/item/32450127290.html?spm=a2g0s.9042311.0.0.5ccc63c08IhJp0) - 2...

This is a remix from https://www.thingiverse.com/thing:4674214 i have constructed my own panel and integrated my own ventilation control via an arduino nano.

Octoprint case for 2 printers Requires: 1x - Raspberry PI3 B+ 1x - 2x Rele Module 2x - Brazilian power plug 1x - Power cable

-------------------------------Octoprint GPIO Setup------------------------------------------------------- Load last Octoprint here: https://octoprint.org/download/ WiringPi installieren: gpio -v sudo apt-get install git-core sudo apt-get update...

I personally did not want to leave on my Raspberry Pi 4, running an instance of OctoPrint, all the time. Therefore, I decided to create a power button to attach to my i3 frame. While designing and testing I also realised that I did not want the fan...

I personally did not want to leave on my Raspberry Pi 4, running an instance of OctoPrint, all the time. Therefore, I decided to create a power button to attach to my i3 frame. While designing and testing I also realised that I did not want the fan...

Inspired by the fantastic model from @Zejott_301841 (https://www.printables.com/model/465225-led-printer-status-beacon-light/comments) i decided to make my own version of it.As you can see in the photo i used an 7.65mm aluminium profile as cable...

https://www.thingiverse.com/thing:211641/#files To get a better image on your PiCAM too go to the Config.txt file and enter the following line anywhere: &# Raspberry Pi Camera V1/V2, 1080P, partial field of view (16:9 aspect) at 30fps &# Notes:...