octoprint ender 3 s1 3d models

A remix of the tray insert published by turbett1. I removed the tray bottom to reduce print time and increase storage volume. ...I also made the snips easier to remove by adjusting the storage between the handles to allow room to get your finger under...

No support needed. Print like how I oriented in the picture. Need a 60mm and a 40mm fan for the 6024 version. This version is very quiet. Need 2 40mm fans for the 4020 version You WILL need to relocate your BLtouch. ...There are relocation mounts...

A simple bed-level test to make sure that your printer is leveled correctly !!only print one layer!!

<p>Guides à coller au double face sous votre plateau afin de placer correctement et rapidement votre plaque PEI.</p><p>S'adapte surement à un grand nombre d'imprimantes.</p><p>Je les ai placés seulement à l'arrière du lit pour donner la position mais...

So you bought Creality's silicone bed screw mounts to replace the springs and you noticed one of the silicone mounts is shorter than the other. These fix that. Print 3x of the 5mm mounts and 1x of the longer mounts. 5mm mounts are about the same...

This is a remix of the project from here https://www.thingiverse.com/thing:5767800 by bensoneh. The issue with the original thingy was that the display mount was too close to the pi case so the top cover would not fit. Also the screw holes seems...

Don't try add-ons. Ditch the stock cable guide completely. Save your ribbon cable from premature wear. I had to alter the retainer clips slightly to get it to fit. Pull the retainers out and snip the outer nubs off. ...From there everything should...

A basic mount designed to work with( https://www.amazon.com/Meggsi-Hygrometer-Thermometer-Temperature-Greenhouse/dp/B07W9LRV4K/ref=sr_1_1?crid=38ATJFT4G8C4W&keywords=b07w9lrv4k&qid=1661126353&sprefix=b07w9lrv4k%2Caps%2C131&sr=8-1) For checking temp...

Added a hole to put nozzle cleaning needle in and decreased the fillament usage. ... Can be printed without supports.

Remix I made to fit my Tapo C100 in the mount.

This design mounts the LCD at an offset atop the base to save space on the side of the printer. Use M4x12mm bolt and M4 nut to mount the LCD. ...Use the original LCD M4 bolts to fasten the 3d printed mount to the base.

this is an alternativ to the heatbed cable chain many are using just use TPU, no supports required

Da am Original die Kabel von Endschalter und Steppermotor der X-Achse relativ ungeschützt waren habe ich die Kabelführung überarbeitet.

I tried some of the FAN ducts, but was never satisfied, so drew one myself. The Fusion360 file is attached. The FAN duct is as close to the original as possible, but has a little more distance to the hotbed. The design has no corners, so the air...

I designed this bracket to relocate the filament run out sensor to the middle so the angle of the filament is centred when having 2 spools fitted. ...Print on its side to avoid layers from separating.

This is a Remix from a Mount previously uploaded. The holes where too small for the head screw in my printer. I decided to redo with similar dimensions removing bottom hole and making top hole bigger for the screw in my printer. I've also made...

Quickly remixed the mount to use a M3 Hex Nut to secure the filament sensor to it's original 90 degree bracket. You can probably use the original screw it comes with, but the hex net it's needed. Also made it 10mm shorter to achieve a faster...

Normally, the filament runout sensor is directly screwed onto the filament spool. After I built a enclosure around my printer and placed the spool outside the enclosure, this was no longer possible.This sensor holder can be clicked directly onto the...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/fGgzhn7VN2O

An upgrade to fix the not linear Y Axis extruded bar

Remixed from the below model. Fits without hardware, just clip it on. https://www.printables.com/model/403964 Thanks to JLOJ, the original designer. ... Original model at thangs.com: https://social.thangs.com/m/853250

Remix for Raspberry PI 4b with GoPro Mount for LC26 picam IR-CUT LC26 I put the 3mf files with the unassembled parts so that you can adapt this to the raspberry box of your choice

I remixed Nandomeier's design so the clip is on the other side of the Z-axis guide, this way it lines up with where my cable comes out from under the printer.

It can make your 3D printer more sturdy and reduce any annoying vibrations. However, you should be aware that using this kit will mean losing the original LED light bar. If you're using klipper, you can measure the resonance and see that the...

This is a Remix from the V3 version from Aiirik, but I replaced the mount for the V2 Version. Worked very nice for me. ...

Tool holder that slides left on to the printer, no screws needed.

Remix of great Z-axis mount for a popular C270 webcam by @BKT_C5. My part of design is a little bit sloppy, because I was too lazy to do it from scratch and used piece of my own mesh for railing mount. See screenshot for how to place on the...