octoprint ender 3 s1 3d models

This is a remix of the original design by PH1933. I just added a countersunk hole to secure it better. ... You will need: M3*12 bolt M3 T-Nut Printed with CHEP Cura 5 Extra Fast Profile with 20% infill

Useful in case you don't want to use the delivered spool holder (where the filament sensor is to be mounted). ...For best results rotate to its side before printing.

My first post !

This is a full CAD recreation of the bedside clamp as the original had messy geometry. ...Moreover, it was too short using the description provided with the referenced parts, which was: > *You will need 1x Bed clamp, 1x Frame clamp, 18x Chain link,...

Idea came from https://www.thingiverse.com/thing:5444181 but I found the clip too narrow for the cable so made a new clip with more allowances from scratch that fits much better. Print it in the same orientation as in the images, not as it comes...

I made this as a simple bracket to attach a ADXL345 to a sprite extruder. ... The holes did come out a bit tight on a low quality print setting but i just run a 3mm drill through the holes.

Just a remix so the X and Y belt tension knob match the screen knob

Someone wanted this scraper with a cutter built in.

- Moved the CR Probe up. ... - Enlarged the screw hole 10%

This puts your ribboncable on the front instead of the back and coupled together with my other model that protects the turning of the ribboncable on the contact make this great

<p>Layer height 0,28mm</p><p>Infill 100% !!!</p><p>Compatible with accelerator MPU-6050/GY-521 (demand mechanical and electrical interference in LCD board)</p>

This is a remix to print in less then 5h

This mount relocates the probe closer to the nozzle. This results in a better first layer. Therefore, the hot end fan needs to be relocated to the right side. No rewiring required. Also, the new mount is lighter than the original one.For me, the new...

I could not find a good enough webcam mount for either my webcam or the printer I am using so I made my own. it mounts on the right side of the printer head bar. ...There is also a hole for a screw in the print just if you would need to secure it more...

So that the ADXL345 can be easily mounted, the holes for brass inserts are present. ...M3x6mm brass inserts can be found here: https://www.bastelgarage.ch/m3x6mm-gewindeeinsatze-messing-insert-50stk

I needed a mount for the C920 and liked the other design, however the C920 base is a little wider. Factory screws hold this in place, although I did notice a slight spread apart where it attaches to the printer. ... Just added a new version, more...

Simple replacement for the original bed handle. Designed it for my IKEA Lack Enclosure because the standard was too long for my purpose. You can use the original screws. ...

Fits the length of the tools perfectly.

This is an adaptor to attach your Sprite or Sprite Pro extruder to an MGN12H linear rail. Fitting _________ Remove the extruder from the mount. Remove the belts from the slots, then loosen the screws securing the lower wheel, then slip the...

This end cap replaces the one supplied, and allows both standard size spools and small spools to be slid onto the shaft without dismantling the end cap

I loved the minimalist bed handle by schroedaa, but it was a bit too tall and the parts cooling fan was impacting the handle, so I trimmed the handle pull down by 5mm. ...Everything clears fine now and there's still enough handle to pull on.

I wanted to mount my RPi 4 running Klipper where the touchscreen After printing it should slot into the touchscreen mount just fine - the Pi can be mounted using M2.5 screws or standoffs Enjoy!

Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142

Just a remix where I made the design watertight. ...All other design aspects are from the original creator.

There are other models made by different authors, mine has two differences.different shape of endstop pcblow profile, doesn't touch the bed with silicon spacersfill free to modify on onshape

Combined the adapter from the filament spool spinner and the ship's wheel design. I'm new to manipulating 3d meshes in Fusion 360 so I'm not sure if the two objects were combined in the proper way, but this part does not need much structural...

<p>This is a easy to print filament guide for all printers with 20x20 profiles.</p><p>You need a 8x16x5 bearing, a M3x20 screw and a M3 “melting nut”.</p><p>No supports needed.&nbsp;</p><p>Das ist eine Filamentführung für alle Drucker mit 20x20...

<p>No mounting hardware required - simple 'plug&amp;play'</p><p>I printed mine in PLA with 20% infill, 0,2mm resolution and 0,4mm line width - no supports needed.</p>