octopi case for ender 3 v2 3d models

Original Electronic Workhorse Ender 3 Pro / Ender 3, Dual 40x40 Powerhouse Fan Upgrade

It is just a tool holder for the Ender series but with a sliding mount instead of press-fit, and some SD/microSD card slots.Minimal supports needed, just for the sliders.

... near by and hadn't found anything I liked, so started learning how to use Fusion360 and designed this. ...It slides into the rails on the bottom of different Ender 3 models. ...I found it printed best from a corner, with a small raft and supports.

Some rounding on the case.I have areas to improve this but as it is working as it is I may not work on v2 for some time to make some improvements. ...Currently functional but could be prettier!In the photo on my current printed version the horizontal...

I only used this for tuning input shaper, then removed the mount.This model uses the space from here: BLTouch Spacer/Screw Cover for Ender 3 Pro by onpdm - ThingiverseI don't have a photo of it mounted, I'd removed it and started a new print by the...

Cover for the Ender 3V2 Display. I recommend printing the frame in an upright position with supports enabled in order to make the snap fit work better. ... After assembling you can mount it with double sided tape to the screen as shown in the picture ...

... on the back. PLA seems to work best, as it is stiffer and this part wont see heat. You might also find printing the slide at 101% size makes it fit REAL nice.This is a remix of “Ender 3 Adjustable Endstop (3 and 3 Pro)” on thingiverse by Mach_Zero

Upgrade 3: Cover for the side fan in order to hide the screws and improve the look: https://www.thingiverse.com/thing:4744145 ATTENTION The fan of the front scrapes on the grid, so it is necessary to pull the center of the grid forward to make a...

Upgrade 3: Cover for the side fan in order to hide the screws and improve the look: https://www.thingiverse.com/thing:4744145 ATTENTION - The fan of the front scrapes on the grid, so it is necessary to pull the center of the grid forward to make a...

This is a remix of https://www.thingiverse.com/thing:5179838This remix takes the mount the fits the Ender3 V2 hotend shroud and modifies it to fit a Mitutoyo 2046 dial indicator. ...The mount is a direct replacement for the rear cover of the dial.It...

Please use support when printing part 1,2,3. ... also use raft when using PETG filament for avoid elephant foot

I accidently printed this thinking it would fit my V2 (I know I didn't read his description) So I made this fit. Just elongated between the two semi circles. Fit snug for me. I may remake this and make it a mm or two longer if there are too many who...

I bought the Raspberry PI to have Octoprint in my Ender 3 v2. The Pi that I bought came with a nice case and some accessories. ...Wanted to keep the case, so designed a holder for the Pi with the case and a mount for the camera with the case.

... connect to biqu 2. lossen the gantry wheels(only need a few mm) and plece the mount under the screw 3. connect to the plate with 2 m3 and then tighten the wheels screws update-19.6.22: top and bottom screw holes are now slots for easier alignment

you can replace this with the cap of the original spool and have a double spool as well, its width is 3 cm so any filament can fit

Remix of https://www.thingiverse.com/thing:4604339Wanted to make it fit a Pi 3 A, so moved screw holes and changed usb slots.To print, follow his guide.

Cover Qr code modelize with a bmw logo for the fans of the brand.

Needed a place to mount an ADXL345 for use with Klipper, so I made this simple remix. ... You'll need to tap the holes for the ADXL345 to use short M3 screws to mount it.

This putty holder can be attached to the rame. ... LxWxH: 45.5x24x45 mm For max. ...putty width: 37.5 mm

Bed leveling bushing to remove springs. ...I have also added a extra 17mm tall bushing for the cable tray on the back of the bed.

Just a little roll for to put between the original holder and the filament spool, so it doesnt wiggle arround that much while printing.

I upgraded the loud fans to quiet 120mm fans.\r\n\r\nI crafted these custom legs for added vertical clearance.\r\n

سلام عليكم this is a prototype, i share .f3z file for remix or upgrade for now its working fine and easy to install just need screws M3 to hold it the point of this design that you can level it with the nozzle touching the bed i hope its help with...

... Spool Mount](https://www.thingiverse.com/thing:5237821). ... It bobbles with the back and forward movement of the filament but still holds strong for a lightweight guide; More than strong enough to serve its purpose. ... Designed for 1.75mm filament

Easy to print little LED-Lightbar for LED-Stripe Double print Lighbar for left and right side, Konektor ones to connect both sides of bars ad as much Clips to hold LED-stripe as you like optional Kabeslip to hold LED-cabel if wanted 300mm x 1.5mm x...

سلام عليكم this is a prototype, i share .f3z file for remix or upgrade for now its working fine and easy to install just need screws M3 to hold it the point of this design that you can level it with the nozzle touching the bed i hope its help with...

... is a separate piece so that you can customise easily your own for your brand of webcam. I added the "hdfull" mount for this cheap webcam that a actually use (work with octoprint): https://fr.aliexpress.com/item/4001103115485.html ->1080p Style4

Remixed to allow a different orientation for the spool holder on my printer. ... This angled version mounts on the right or left side and holds the spool above the printer bed without colliding.

For example, in most variations of the "Ikea Lack" print cabinet. The position of the display does not block the movement of the print head, the movement of the print bed, or the accessibility of the small tray at the bottom of the printer. ... For...

Improved the moving upper part by - widening the fin so it is a snug fit in the channel - adding a T nut which when tightened holds the top end within the channel (but still allows movement) - added pocket for the Z stop PCB to be installed in...