octopi 3d print

If you need a support for mounting the raspberry pi zero 2 w on your 3d printer, you can find this project very useful.

The original file from JZE exhibited a mesh issue that became apparent after being sliced within S3D. ...Following repair in 3D Builder, the file was successfully re-uploaded for further use.

This is a remix of 2 great designs. https://www.prusaprinters.org/prints/4038-malolos-screw-less-snap-fit-raspberry-pi-3-model-b andhttps://www.prusaprinters.org/prints/974-prusa-mk3-sideboxes-for-some-tools Needed to use my “old”...

PS: The back cover is the original from Luc_e Print Settings Printer: Original Prusa I3 Mk2 Rafts: No Supports: No Resolution: 0.20 mm Infill: 20% Notes: Top printed in blue translucent PETG from Prusa Bottom printed in black PETG from DAS FILAMENT 6...

Print Settings: Rafts: No Supports: No Notes: Printing with PLA, I didn't need a raft or supports. Cleaning up a piece of sagging filament was the only required effort. Post-Printing Instructions: Place the RPi upside down in the cover and position...

It will securely attach to the inside of the print frame, opposite where the controller board screws are located. Two nubs take the place of traditional screws, allowing for effortless attachment of the pi case. I've also planned for a bed-mounted pi...

... 3/3+ Models. ... Please download the latest V2 version if you have already downloaded the original before printing. V2 corrects the error of incorrect ethernet/usb port configuration on the rear of the unit. ...(Pointed out by nhania.Thank you!)

... Pi B+, ensuring a seamless fit with its accompanying heat sinks and a 4-pin Power over Ethernet (PoE) connector. ... I've also included a suggested STL file, "Pi Camera Mount," which benefits from being printed on a raft to achieve optimal results.

this is a minor remix of BaudlerArtDesign's Rpi 4 case found here : https://www.thingiverse.com/thing:1815268 This resdesign was made to help with exhaust airflow slightly, along with adding rail mounts to the bottom shell to mount it on the left...

... is a Remix of https://www.thingiverse.com/thing:4328596 and https://www.thingiverse.com/thing:434600. ... Screws needed: 7x M3-nut 5x M3x16 2x M3x8 Only the sphere rod was printed with brim. ... Fan guard: https://www.thingiverse.com/thing:2505568

(Though, you could print it lying flat with support if you prefer.) The other parts don't require any support whatsoever. I'm thoroughly pleased with how the clip attaches to the shelf and could definitely reuse this design for others if I want to...

This is a Remix of https://www.thingiverse.com/thing:4328596 and https://www.thingiverse.com/thing:434600. ... Screws needed: 7x M3-nut 5x M3x16 2x M3x8 Only the sphere rod was printed with brim. ... Fan guard: https://www.thingiverse.com/thing:2505568

... the Pi Zero, which should work seamlessly with most Pi Zero enclosures (though it's worth noting that it isn't strictly necessary). ...I encountered no issues whatsoever during the printing process, and everything assembled perfectly without a hitch.

On the opposite end of this dowel lies an additional printed piece, its sole purpose is to firmly hold one end of your USB extension cable into place. To enhance WiFi connectivity on my setup, I chose to place my adapter up high to better catch the...

The rest is identical.Print instructionsThe bottom get can get a bit hot so I recommend printing it in PETG or higher temperature material.The bottom is designed to print without support at 0.2mm layer height. ...It should work with other settings.</p>

... w attached to the frame utilising existing screw holes left unused on the printer. It stays conviniently behind. There is a hole planned for a camera ribbon, however not recommended with a pi zero as you may encounter a decrease in print quality.

I've included all necessary parts so you can print without searching for them separately: The fan cover is taken from JKSniper's Thingiverse page - [2076234](https://www.thingiverse.com/thing:2076234). ... The back lid comes from hackoholic's...

... the case so frequently to make adjustments that I stripped the screw holes, so this housing is pressure mounted. I have come across designs that lengthened the casing, I chose to break it into 2 cases to enable it to fit on an Anet A8 print bed.

This is a Raspberry Pi camera mount I designed for a desk lamp I bought from Amazon to illuminate my print bed and monitor it during prints. It allows me or services like the spaghetti detective to clearly see the current print without needing super...

Installation ===== * loose the right corner screws in the base of Ender 3 S1 pro, push the my mount print into and then put screws back * after that the pi case can be installed to the left with the dove tail joint * cam holder is easy as seen in...

I also made it sit flush against the frame because I had trouble with the cables during printing. As it doesn't have a cover anymore, it should fit every cooler model. The GeekPi ultra thin ICE Tower cooler uses M2.5 screws and a mounting plate,...

... unused on the printer. The design stays conveniently behind, out of the way but still accessible when needed. A hole is planned for a camera ribbon, although it's not recommended with a Pi Zero as this may result in a decrease in print quality.

A Webcam Mount for the Creality CR-10 3D Printer. The mount holds a Vilros Raspberry Pi Case securely and the brackets attaching the webcam are fastened directly onto the Pi Case. The Webcam displayed in the images features IR capabilities, but as...

This part prints without support at 0.2mm layer height and should work with other settings. Two M3x12 screws are required for mounting; M3x10 will work if necessary. ... Revisions: On June 3, 2020, based on RobobTV's Make and feedback on the little...

Note: Both parts are printed upside down on the build plate. My settings for supports include: 10% overhang Interface layer 0.15 Contact Z Distance Parts required for assembly: 4 x 10mm silicon pads/feet/bumpers (optional) 4 x M3 x 10mm screws 4...

Currently functional but could be prettier!In the photo on my current printed version the horizontal supports to hold the camera ribbon have broken off.The mount is designed to hang off the right hand side of my Ender v3 SE bins (thing:6453586), and...

When printing this design, take note of the tiny vertical tube on the main case's wall where the heated bed wires enter the Einsy enclosure. ...The black filament wire should be guided through this tunnel to keep it secure and prevent any issues with...

This is a case I designed, and a base mount i redesigned to work with my Raspberry Pi 3b+, Ender 3 V2 and a 3.5" OSOYOO touchscreen: https://www.amazon.com/gp/product/B08634Y16L/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1 -Print the Base and...

Once connected make sure your USB cable is in the 2.1A not the 1A or it will under voltage and fluff your prints. ... *Should you still get underpower message in Octoprint - try a different USB cable.* This was a solution based on many phone...

... it up the front. If you prefer Wi-Fi, you can skip the Ethernet wire - I just like having a wired connection. I've provided STEP and Rhino 3D (.3dm) files so you can remix or modify them if needed. ...Just be considerate and credit me in some way.