octo gate fightstick 3d models

The Octo hole of mseminatore's Joystick oct-gate was slightly too small for my cheap generic stick and the button presses where restricted. I used Fusion 360 to open up the hole by a 1mm. Category: Toy & Game Accessories

The joystick opening on mseminatore's Octo Hole was just a bit too narrow for my standard issue controller, causing the buttons to be pressed with limited freedom. ...I employed Fusion 360 to enlarge the opening by one millimeter.

The eight-way gate is a direct replacement for the square gate in Neo Geo AES joysticks, providing an authentic gaming experience with precise directional control. ...This upgrade seamlessly integrates into both the original stick design and the iconic...

This is a fightstick-style controller made using Cherry MX-compatible mechanical keyboard switches. I used an Arduino Pro Micro clone, but it could be used with any other board. For attaching the bottom plate I used 3x10mm wood screws. ... ...

This is a fightstick-style controller made using Cherry MX-compatible mechanical keyboard switches. I used an Arduino Pro Micro clone, but it could be used with any other board. For attaching the bottom plate I used 3x10mm wood screws. Arduino code:...

Basic screwable top ball for fightsticks/arcadesticks

American Style Fightstick The threading is M6x1.0

This was a purpose-built model to replace the water-damaged particle-board mounting board in a fightstick I'm restoring. Probably not super useful outside my case, but thought I'd throw it up in case others found it useful for remixing. ... The screw...

This was a purpose-built model to replace the water-damaged particle-board mounting board in a fightstick I'm restoring. Probably not super useful outside my case, but thought I'd throw it up in case others found it useful for remixing. ... The...

This is a mixbox-layout fightstick controller that uses four Cherry MX-compatible mechanical keyboard switches, six 30mm (Sanwa OBSF-30) and four 24mm (Sanwa OBSF-24) arcade buttons. I used an Arduino Pro Micro clone, but it could be used with any...

This is a hitbox-layout fightstick controller that uses 24mm (Sanwa OBSF-24) and 30mm (Sanwa OBSF-30) arcade buttons. There's a version with 6 and another with 8 action buttons. There's also a 218mm-wide version that should fit on an Ender 3...

This is a mixbox-layout fightstick controller that uses four Cherry MX-compatible mechanical keyboard switches, six 30mm (Sanwa OBSF-30) and four 24mm (Sanwa OBSF-24) arcade buttons. I used an Arduino Pro Micro clone, but it could be used with any...

This is a hitbox-layout fightstick controller that uses 24mm (Sanwa OBSF-24) and 30mm (Sanwa OBSF-30) arcade buttons. There's a version with 6 and another with 8 action buttons. There's also a 218mm-wide version that should fit on an Ender 3 printer....

Another Fightstick Case, this one is significantly smaller and simpler in design. It should be easier to manufacture if you have the necessary tools. The first setup in the Fusion 360 file yields a higher quality appearance but takes longer to...

Here's a full frame for an Arcade Fightstick. It requires a large printer since the full dimension is approximately 30 by 21 centimeters. I used a metal plate to close it, along with some screws for closing the stick - at least one must be short to...

Here's a full frame for a Arcade Fightstick. It requires a large printer since the full dimension is close to 30*21 cm. I used a metal plate to close it, as long as some screw for closing the stick ( at least on must be short to avoid drilling your...

Here's a full frame for a Arcade Fightstick. It requires a large printer since the full dimension is close to 30*21 cm. I used a metal plate to close it, as long as some screw for closing the stick ( at least on must be short to avoid drilling your...

Arcade controller (probably call it a Fightstick if you're in the FGC). Designed to play fighting games/ arcade games (Street Fighter, Tekken, Gauntlet, etc.). Since the front panel is separate from the box, the controller can be used by left-handed...

Here's an Iron Man (or War Machine) inspired Raspberry Pi, PS4, and PC compatible fightstick, including everything needed to play anywhere at any time. The .stl file is dimensionally accurate when exported with mm as the export unit in SketchUp. I...

Octo Skull.

Octo Skull.

Demo Octo-rotor

#3DBenchy + Octopus = Octo-Benchy

rick sanchez as an octo.

No description is available at this time.

its so cute

No description provided.

Underwater Environment Rendering utilizing Three-Dimensional Modeling Techniques.

Test .stl not Printed .