octane apex 3d model

Basic overview:This is a drop in replacement barrel for the Dart Zone Solo Pro that is designed to allow it to fire mega darts, but I designed the model in a way that it can not only also still fire half darts, but fire rival ammo too! It shoots Mega...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

(In the future, I'll model a printable screw-gun interface for people who can't get the part in question.) 4.#6-32 brass nut, 1/4" across (measured face to face), 3/32" thick (optional) McMaster-Carr 95130A120. Fits into a pocket on the gun carriage,...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

they are built into the models. Use the provided M2.5x10mm self tapping screws by default unless told otherwise. As an alternative to jig cutting, a drawing for manual hole drilling is also provided. In addition you will need: - Hot glue...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

A few copies of it will be printed, for two reasons: cooling during print and as spare if some print fails. raketplattform överdel_xy0.4mm_z0.2mm_ELIXIR_ELIXIR_ELIXIR_ELIXIR_ELIXIR.3mf raketplattform...

Slice your model in your desired software and save your gcode 3. Place the created gcode in the same folder in which you extracted the exe 4. Double click to run the exe 5. Type the number of the option you wish to use, for the towers included in...

Its light and super stiff if printed in ABS 100% infill. Included are all the .STL files for all the models. The frame is quite light and stiff. I threw the frame over and over against a wall and from a 5th floor balcony and it survived...

To split it with ease, right-click on your model within Cura. When preparing your parts for printing, make sure flat sides are aligned downward. For a smoother print process, consider setting 0.1mm layer height and 40% infill as defaults. Here is...

Moreover….Sitag astonished me a lot because actually….they continue to make and sell the same model: the famous “Sitag Reality”…which costs now around 700€ !!!Therefore, I decided to try a repair with my engineering skills and a big dose of...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

A custom-made enclosure specifically designed for the Raspberry Pi computer assistant Assistant assistant A bespoke casing tailored to fit the Raspberry Pi device. assistant Created especially for the Raspberry Pi, this is a one-of-a-kind case. ...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Wiring/Plug: This waterproof power supply is...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...