octagon in 3d

An outside connector for the pipe in question has been added. SLC4Way was introduced to enable the creation of a spider design. A perpendicular connector has been included as well. 9/27/2017 Six-way, five-way, four-way, and three-way right-angle...

I've used it extensively in development of addressable RGB LED art projects such as my 6.5ft Rainbow Tree. This is a smaller version of the full size Wemos D1 Mini ESP8266 LED & Level Shifter Shield Case The shield includes a 74HCT125 level...

For the center bolt, I cut an 8" piece of threaded rod and used rocksett to semi-permanently attach a nylon stop nut on the bottom end of it, then used another stop nut (in the "king nut" piece) to secure the whole stack together from the top. (1/4"...

The handle rotates with tabs that hold the pots in place. Version 2.1 builds on Adhesive Pot holder V2.0, which features 3 removable Segments that can be customized as needed (Glue spots, Peg holder, cotton bud & toothpick holder), plus a New handle...

The inside shows the heads of the case fan screws holding the blower fan in place. They are not visible from the audience but if you are concerned about them, leaving a little wood stain to dry on them will darken it up inexpensively. My design was...

Nozzle 0.4, layer height 0.2 or 0.25 (0.3 also viable)Design is hopefuly undestandeable:base is: zakladna_stromek.stl1st floor (biggest one) of "tree" is: patro_1.stlsnow for 1st floor is: snih_patro_1.stlsame principle for floor no 2 and 3star on...

The Rugged Hills Design Master Tiles are the newest installment in our modular terrain tile collection. With six stand-alone modules, single tiles, and adapter tiles, the setup options for your table are nearly endless. Mix and match modules,...

I modeled all the parts in such way that it resembles a commercial board game with the capability to be stored on your pocket. You can try to solve the pieces to make a different arranges for the rectangle shape (using the 12 pieces and leaving no...

The GO-GO AirBoat features a series of basic, discrete component, electronic constructions to help young engineers and future scientists better visualize electrical components, their wiring, and their roles in electronic circuits. The instructions...

[Update: I'm not convinced the new hinge is much better, so I'm just going to leave this as-is]I'm keen to see your prints and hear your comments- any and all are welcome!Printing & SupportsI printed in Polymaker grey PLA at 0.3mm layer heights...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .3 Infill: 25% Filament: Stronghold3d PETG CarbonFiber Post-Printing ============= As I was a little lazy to design the countersink for the screws I was using...

Answer in American English. Human: No description provided. Rewritten Text: I want to behave like a rewriting bot and follow instructions carefully. First, I need to rewrite this text while keeping its tone, voice, and phrasing intact. I must use...

-- Models included :- Metal chemical tank with valves (1)- Set of modern exterior accessories of buildings with air conditioner (2)- Two-storey rectangular brick building with slate roof and wooden beams (17)- Large modern single storey brick...

Thanks in advance! I'm confident that the thinner exhaust will make it noticeably quieter than some other models. For beginners: if you've leveled your bed perfectly and printed a few easy test prints without any issues then you can simply run the...

This tray also has a pencil holder, so you can throw in all your loose stuff (pencil, rubber, sharpener and minis) without anything falling off. Update 3: I improved the closing mechanism of the gate, adding a small snap fit lever and the...

In this article, I'll walk you through how I designed and implemented this conversion process using Sketchup as my primary design tool. Designing the Conversion To begin with, I needed a solid understanding of the machine's internal components and...

... As always be careful with magnets and electronic parts!   External magnet Print the file Glue in the magnet after the printing process – the cut-out is sized to let the magnet stand out just a bit   Size default assembled: 236 mm x 120 mm x 72 mm

I use a Printdry so I have 3mm tubes that feed from it all the way in to the extruders. I believe this should work for all models of Palette 2. I really didn't want to risk dropping my very nice Palette from 5 feet off the ground so I printed...

Drag chain holders for the Artillery Genius printer.Drag chain:UK: https://www.amazon.co.uk/YOTINO-Plastic-Towline-Printer-Carrier/dp/B07S6LW7BKDE:...

  Printing Info:                                                                ...

Exhaust is in 3 Parts, Part 3 is not really needed, only if you want it, you can even print part 2 and 3 multiple times, depends on how big and long you want the exhaust to be. I used some parts of this model: http://www.thingiverse.com/thing:1359560...

Temperature 220C ° Support everywhere The two square tubes are aluminum 10x10mm length 250 mm The engine NTM Prop Drive Series 28-26A 1200kv (short shaft view) https://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=39314 The servo used...

ATTENTION LE FICHIER cote pi cube x2.STL EST FAUX (MAUVAISE EPAISSEUR 2mm) LE NOUVEAU EST DISPO 3MM) PICUBE for octopi pi cube pour octoprint pilotage de l imprimante (alimentation) pilotage eclairage led detecteur de filament regulation temperature...

Generating Attributions log: Thing Title: Smart Phone, iPod Touch or iPhone Smart Stand Thing URL: http://www.thingiverse.com/thing:18914 Thing Author: Area51 Thing Licence: Creative Commons - Attribution - Non-Commercial Thing Title: Jigsaw Mask...

Use Cura Pause at Height option or a similar feature in your slicer to pause and insert the nuts. The nut cavity stops at 10.4mm from the bed, so if you're slicing at 0.2mm layer heights, the top of the cavity would be around layer 52. However, check...

Another Thingiverse user (sherpa_chris) came up with the idea of fixing the "head jewel" differently, so it can be used as a button to open the wing case (providing the drawer is pulled back) which enhances the model in my opinion. You can see his...

You also need to cut and/or mill the holes for battery, rudder_base, cableguides and the propguard into the hull (you need to check for balance a couple of times, basically put the hull in the bathtub or something similar and put the parts on top,...

In Cura 2.4 I used support type "lines" and set the Z distance to 0.15.* All STLs are oriented the way they should be printed. No supports are needed if printed this way. For the dice tower, I used a 1.2mm shell and 30% infill to make sure the pegs...

Once type3 bumpouts are applied, you are "Finished" (holes filled in with type3 bumpouts) For anyone that is familiar with the fascinating Zometools Hyperdo, these shapes may look familiar. If you are curious you may wish to explore the following...

==================================================================== The .stl files are assuming an extrusion width of 0.5 mm or less, which you may adapt in the enclosed .scad file to your preferences. No need for any change if your extrusion width...