obs ford cup holder 3d models

This part is designed to improve the cup holder of 92-97 obs ford cup holders with the flip up/down center console. It is designed with screw holes but also can be attached using two sided tape. ...It will keep your drinks from falling over and...

OBS F-Series Console Cup HolderFits the center console of F-Series Ford Pickups 1992 - 1996

... the center console. ...It may also fit other Ford models. Similar in design to the original cup holder provided with the vehicle, this insert stands a bit taller and wider to accommodate smaller cups and the slightly deeper driver's side cup holder.

This is a base for a Ford car cup holder. It stops cans and cups going all the way to the bottom of the cup holder. Infill of 15% should be fine. ...The flat part goes at the top and the fins go at the bottom.

I made a Ford cup holder separation with a 19 mm hole. For example, you can use a button for an additional horn. You can sand the surface, but be careful not to destroy the tips. ...(like in the picture)

MY stock Ford cup holder was not practical. This new design works great! Hope this helps you out like its did me, Coffee is life my friend. ... 2 designs if i mount the Double cup i'll post pic for now i like the 2 cups mounted to the T joint.

I'm Adding Cup Holders to My Ford E350 Project. It Only Came with One, and That Wasn't Enough. So I Used My E150 Wooden Template to Create a New Holder for My E350. This Design Can Be Resized to Fit Most Van Center Consoles. ...To Make the Opposite...

It originally came with a single cup holder, which was insufficient. I utilized my E150 wooden unit as a model to create an additional one for my E350. This design can be easily scaled up or down to fit nearly any Van Center Console. ...To create the...

Similar to the original cup holder provided with the vehicle, but tweaked to accommodate smaller cups and the slightly deeper driver's side cup holder, this insert stands out with its slightly taller and wider profile. Print Settings: * Printer:...

Might fit other Fords. Much like the original supplied with the car but a little taller and wider to account for smaller cups and the slightly deeper driver's side cup holder. Print Settings Printer: Vellerman K8200 Rafts: No Supports: No...

Here's a perfect fit for your 1987-1993 Mustang: a custom cup holder (and change tray) that fits seamlessly into the ashtray space. The clever design slides down easily, leaving no gaps or obstructions. I put it to the test by driving with a full cup...

A replacement cup holder insert for a Ford Edge

I modeled and printed replacement cup holder inserts for my 2016 Ford Explorer. The model is 80mm which will fit the front cup holder. ...Down size by about 10% to 70mm for the rear cup holder.

The 08 Ford Fiesta cup holder seamlessly replaces the coin holder, boasting a sturdy design that has been meticulously printed and rigorously tested to ensure a perfect fit.

I designed and fabricated new cup holder inserts for my 2016 Ford Explorer, matching its specifications. The original model measured 80mm in diameter, a perfect fit for the front cup holder. ...To accommodate the smaller rear cup holder, I scaled down...

This is a cup holder riser for the Ford Galaxy (UK model 2017), probably fits most other cars. The cup holders in the centre console are too deep and a can of drink or standard disposable cup will sink in. The risers provide storage space and...

Not sure who the idiot at Ford was that designed these oversized cup holders with lock jaw brackets. The fingers on the sides of the cupholders are so tight that I practically wreck my car every time I try to pick up my drink or set it into the...

The modest European coffee cup sinks away in the cup holder of the car. Dangerous!This model is parametric and can thus be modified for other cars or cup sizes. A Freecad file is included. The base of the printed model is 20 mm height (to lift the...

For the Chevy OBS lovers . ...have a phone holder or a paperweight . ...Enjoy and Thanks.

My Opel Carsa UTE do have a cup holder but it is so small and shallow that when I go around a corner it falls over and when I installed a speaker box at the back it slightly covered up the cup holder, the doors sort of have cup holders but then I...

replaces ashtray in bullnose generation of ford trucks. ...Confirm with the picture to make sure your truck has the same center section of dash and dash and roughly 7" flip down ash tray slot before committing to the long print.

Remade Cupholder. ...This cupholder is one inch deeper. The original was not deep enough and did not hold bigger cups.

... ...In the picture it just shows what i had around the house, but will probably get something more stylish. As an added benefit, the cup part holds the key perfectly. ... I added some felt to make sure it doesn't scratch, and the for is perfect.

These are replacement parts that are commonly (at least I assume since my sister and I were both in need) lost/broken on OBS ford trucks. Tested on '95 F150 XL. The side rails have been modified from the original design to make printing easier, the...

Ford Kuga / Ford Escape Cup holder for small cans.

The old plastic in my OBS dash has broken, I'm hoping this will help secure the instrument panel. ...There's a left and right insert to fix whatever is broken on yours.

Basic Cup holder insert for a 2016 Ford Expedition to hold a pop/soda can.

This cup holder adapter 1999 Ford F150 and other models. Water bottles, soda cans, etc. keep falling over when turning. So, I made this adapter to fill the space between the OEM holder and the drink. ... This solved the problem

On particular models of newer Ford Broncos, there are no cup holders in the back seats. ... I made one that hooks into the plastic mesh on the backs of the front seats.

This is a first design. ...This is a Dual Cup Holder for a Ashtray replacement for a 1973 Ford Mustang Mach 1 Fastback. ...This may fit other cars as well.