nzxt ssd mount 3d models

this is a mount for the corsair commander controller. ...it is designed to fit the ssd mount in the nzxt H510i case.

Simple bracket mount to install a 3.5" HDD and a 2.5" SSD into the NZXT H1 v1. I designed this bracket to be able to install a 3.5" HDD drive in addition to one 2.5" SSD into my NZXT H1 v1 PC case. Just remove the original 2x SSD bracket and use my...

I designed this bracket to be able to install a 3.5" HDD drive in addition to one 2.5" SSD into my NZXT H1 v1 PC case. Just remove the original 2x SSD bracket and use my bracket instead. You will need some 90° angeled SATA connectors to connect the...

The NZXT case's sleek design gets an upgrade with a straightforward SSD/HDD conversion cover that adds a premium touch without cluttering the space by mounting all three drives.

SSD Bracket to add more hard drives to a NZXT M59 Case. You will need to print x2 Brackets and 4 screws per SSD/HDD. ... The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.

I shifted the mounting hole upwards by six millimeters, resulting in a seamless fit within my NZXT enclosure.

SSD Bracket to add more hard drives to a NZXT M59 Case. ...You will need to print x2 Brackets and 4 screws per SSD/HDD. The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket. Print Settings...

People often worry about heat when it comes to SSD shrouds. To minimize this risk, many individuals choose to print their designs with an open top and bottom layer, leaving only the infill intact. ...This approach is particularly effective when...

The SSD and cable cover is designed specifically to secure on top of the SSD using a strong adhesive tape. ...It's crafted to fit perfectly inside the NZXT S340 Elite case, providing a sleek and organized look for your build.

... custom ROG RYZEN emblem, which meant covering up the holes on the power supply shroud's bottom plate. ...I gladly accepted this challenge and managed to design a new SSD installation solution that would still allow an SSD to fit seamlessly into place.

This adapter mounts the TPcast HDMI transmitter, making it easy to attach the device to your computer using the NZXT Puck without any permanent damage. ...To use it, you'll need a small rounded rectangular prism that comes with this remix.

A headset mount for the PC's with a air flow slot at the top!

The pegs on the back are designed to provide a stand-off and match the depth of the mounting pegs in my chassis - you could remove them or adjust their height to suit. ... Print Settings Printer: Anet A8 Rafts: Yes Supports: Doesn't Matter ...

Mount a high-performance solid-state drive directly into a standard 3.5-inch drive bay.

The device is adaptable to both wall-mounted and freestanding installations, as I was unable to find a suitable solution that met my requirements in either category. Using Fusion 360 software, I created this custom mount from scratch. ... The mounting...

Similar to my EKWB pump / res combo holder: https://www.printables.com/model/291904-ek-pump-holder-for-nzxt-casesThis mounts the Alphacool Eisstation to the vertical bar inside NZXT's PC cases.

The base model is called SSD_Cover_Base and can be used as a standalone cover. For those who prefer more airflow, there are two similar designs with divisions that allow for improved venting. What's even better is that the models with clips fit...

This wall mount is designed specifically for the NZXT H510 Elite case, but its compact size suggests that it may also work with other NZXT enclosures. ...The mounting bracket measures a generous 215 millimeters in width, allowing for easy installation...

I needed a mount for a fourth HDD in my NZXT H510. ...I noticed that there was a removable bracket in the front that had screw holes in it so I took an existing HDD mount and adjusted it to fit the bracket.As with most of my things, I've included the...

... 5' [display](https://www.waveshare.com/product/displays/lcd-oled/lcd-oled-1/5inch-hdmi-lcd-h.htm). ...It can be mounted instead of the SSD holder on the side of the PSU shroud. ... The cables for the display should be routed under the cable bar.

I had two Noctua NF-P12 lying around and decided to mount them to the graphics card side of the case.I let them run on 5V via USB from the motherboard and the GPU temp got down from almost 80C to ~72C.Also the fan is not as noisy anymore with the...

Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...

This is a custom controller holder designed specifically for the NZXT S340 case, accommodating both PS4 and XBOX ONE controllers in perfect harmony. The design is securely clamped, ensuring a snug fit that prevents any movement or slippage. ...For...

This SSD holder secures multiple drive slots.

This is a custom ATX cable mount designed specifically for the popular NZXT H500 PC case. To assemble, simply print the three individual pieces in flat mode to ensure maximum durability. The left and right pieces then click securely into place with...

LED strip mount for NZXT 510 flow case. Might work with their other cases too but not sure. I used glue to attach the led strip to the mount but could also use double sided tape. ...This replaces the parts in the case where the glass snaps into just...

I designed this part to mount the EKWB Kinetic waterpump/reservoir combo unit into my NZXT H210i computer case. You need two M4x12 and two M4 nuts for mounting. I used two spare O-rings from my G1/4 fittings as a vibration damping element. Also...

Ok this is a front LED light strip mount for NZXT H510 it is place on the cable cover so that you can mount a LED strip with Diffuser on it , it is designed to use comandstrips on it instead of glue . ...This turned out well

I designed this part to mount the EKWB Kinetic waterpump/reservoir combo unit into my NZXT H210i computer case. You need two M4x12 and two M4 nuts for mounting. ...I used two spare O-rings from my G1/4 fittings as a vibration damping element.

This is a remix of the iMac HD Mount to fit the a Seagate SSD.