nzxt s340 elite vertical gpu mount 3d models

... this to the power supply cover using some glue, leaving enough room for screws if you're feeling more adventurous. The insert slit is vertical but oriented sideways on the print, and don't worry about support - just snap it off with confidence!

Here is a thing based on http://www.thingiverse.com/thing:70549 that performs even better on vertical surfaces, addressing an issue I experienced with the original version - cables kept slipping out. ...Designated users of 123D, this model was created...

So my LED visor cable (attached to onboard power supply) was getting a little scary when it nearly got caught on the clip of the hot bed during a big job so...BEHOLD!I glued this to the power supply cover but there is enough room for screws if you...

Mount for a haltech elite 1500 to bolt into factory location. ... Might not be super perfect

a mount for nerf elite rails with a hole in the middle

... ...Simply print two (or more, depending on the PSU) mounts and attach them to the frame using 10mm M4 bolts with insert nuts like these: http://www.motedis.com/shop/Slot-profiles-accessories/Accessoiries-20-B-Typ-slot-6/T-nut-B-type-slot-6::555.html.

... prominences within the slots ensure a snug interference fit at screw attachment points, resulting in a seamless and hassle-free installation experience. In my setup, this mounting bracket is designed to be installed directly onto a flat surface.

... to circulate freely without directly blowing onto the parts being printed. A 40mm gap remains between the fan and the ground, necessitating the printing of two identical mounts to provide adequate support for its intended use in this configuration.

It was created in collaboration with my friend ARCHAV2, and our mount was utilized by five out of six Virginia National qualifying teams. The Patriot High School team excelled in these competitions! ... Print Settings: Printer Brand: LulzBot Printer:...

The STL file uploaded deviates slightly from the accompanying photographs, showcasing a base that's marginally larger in size and featuring mounting holes for secure attachment. ...Additionally, this design allows for versatile use as a shelf, offering...

... Printing: I printed the baseplates with wite PETG 0,2mm high and 20% Infill. ... And the holds with black PLA 0,13mm high and 15% Infill Assembly: You can glue or screw the holds to the baseplates. Mounting Info is in the last photo.

I like Chu's bumper, but I needed to mount it at a right angle on a small omniwheel robot. The center hole is covered by the shield socket, but I left it there anyway. You could use it to mount with a flat head bolt before installing the board, for...

Hi, this is my second wall mount design. This one I got inspired after seeing https://www.thingiverse.com/thing:2586068 You need to print 3x SkateWallV2P1 and 3x SkateWallV2P2. I recommend printing first one of each to be sure that the thread...

Hi, this is my second wall mount design. This one I got inspired after seeing https://www.thingiverse.com/thing:2586068 You need to print 3x SkateWallV2P1 and 3x SkateWallV2P2. I recommend printing first one of each to be sure that the thread will...

Created a 2 piece mount to keep my laptop out of the way when using at my desk. It is attached to the leg of my VariDesk standing desk. The laptop this was designed around was ~21mm thick and fits quite well. This part is set up to use 4 M3...

I wanted to mount my Shure ULXD wireless rack but I had no space under my desk, so I decided the next best spot would be to the side of my desk. It clamps on to an IKEA ADILS desk leg (40.5 mm) with 3 M4 screws and nuts each. I would go no shorter...

You could use it to mount with a flat head bolt before installing the board, for example. However, in my case, I'm using the two end holes which are spaced to fit a (so far unpublished) robot base.</p> <p>The bolt holes are deliberately a little...

Designed to be mounted from the outside of the case through a 43.5mm X 116mm cutout, then attached with sheet metal screws or 1/8 inch (3mm) pop-rivets which i think would look better.Things needed to install....Dremel highly recommendeddrill and...

Hi, this is my second wall mount design. This one I got inspired after seeing https://www.thingiverse.com/thing:2586068 You need to print 3x SkateWallV2P1 and 3x SkateWallV2P2. I recommend printing first one of each to be sure that the thread will...

Designed to be mounted from the outside of the case through a 43.5mm X 116mm cutout, then attached with sheet metal screws or 1/8 inch (3mm) pop-rivets which i think would look better. Things needed to install.... Dremel highly recommended drill...

Designed to be mounted from the outside of the case through a 43.5mm X 116mm cutout, then attached with sheet metal screws or 1/8 inch (3mm) pop-rivets which i think would look better. Things needed to install.... Dremel highly recommended ...

I appreciate Chu's bumper design, but I had to adapt it for my small omniwheel robot by mounting it at a 90-degree angle. The center hole was blocked by the shield socket, so I left it in place anyway. As an alternative, you could use a flat head...

A mount for a Akaso V50 Elite with a universal/Go pro style mount for FPV drones.

... To assemble this unique design, set the total depth to 6, specify ELITE as the desired word, fix finger size at 23, adjust finger spacing to 2, and finalize with a total height of 30 and width of 65.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4qOQ2fvxA2F

Compatible with Cooler Master's Vertical GPU Holder Kit V3We are making free to print and modify the design for the rotary knobs that secure our Vertical GPU Holder Kit in place. It could happen that, overtime, or during installation the rotary knobs...

Quanum Elite FPV Camera Mount for the Blade mQX Designing This Project I brought this project to life using SketchUp Make 2016.

Quest 2 battery mount for elite strap. This is to use a mophie powerstation XXL. ...Will add adapters to fit other batteries as well.

Adapter Enables Svive Hydra Elite Microphone Mounting on Svive Hydra Shock Mount Dish, and Possibly Other Dishes Too. To secure the mic to this adapter, use the screws that come with the retail table stand. These screws will provide a sturdy hold...

But mainly this design exists to make space for a full length GPU passing underneath the HDD.Note that this has NOT been tested with an actual GPU yet, and it is suspected that the vertical offset is not going to be enough. To compensate for this, it...