nzxt s340 elite custom front panel 3d models
1226003 3d models found related to nzxt s340 elite custom front panel.
thingiverse
Nzxt nzxt h200i and nzxt h210i front pannel spacing 15mm. ...When installing the panel on the 3d printed spacing, try to align the panel hook on the inside hole of the 3d printed spacing
thingiverse
... not too big and fit perfectly in place. Compared to the original screws, they're much less bulky. These custom-made thumb screws will likely fit other cases as well, featuring a subtle thumb grip on the outside and a threading for small flat bolts.
thingiverse
Replacement front trim panel for the Original Xbox Console. I printed it facing up with support for best detail. ...If clips snap try printing at higher infill.
thingiverse
So my mischievous cat keeps knocking over my power button & yesterday he spit up in two of my usb 2.0 ports, short circuiting them completely. I've had enough of this nonsense, so I created a protective barrier to safeguard the rest of my ports & top...
thingiverse
Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.
thingiverse
Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. ...
prusaprinters
Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. If...
prusaprinters
Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. If...
thingiverse
This is a custom drive mount designed specifically for the NZXT H500 case. Initially, its purpose was to minimize vibrations and noise from my hard drive, but unfortunately, it did not deliver on those expectations. ...I'm sharing it with you in the...
prusaprinters
There's a 0.5mm gap between parts; mask back panel, snap pieces into back panel, and fill gaps w/ JB-Weld or similar. This is to allow everything to fit on the bed and account for tolerance issues. </p><p>Printed with Protopasta CF-HTPLA w/ a...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following settings: Font Size: 4 Points Font: MakerBot Tools Text Length: 150 Characters Width: 80 Units Height: 40 Units Number of Text Lines: 1 Font Style:...
thingiverse
This is a full front panel for SMART SPEAKER https://www.thingiverse.com/thing:3634873 Anyone can cut for the mesaure of your smartphone.
grabcad
The front panel is an essential component, serving as the primary interface between users and the device. It typically features buttons, knobs, displays, and connectivity ports. ...This user-friendly design allows for easy operation and enhanced...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: Font = Arial Black Resolution = High Definition Thickness = Double Layer Text Size = Large Aspect Ratio = Square Border Shell = Off Panel Border...
thingiverse
Customized version of http://www.thingiverse.com/thing:1264391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: BPanel = 0 Police = Arial Black Thick = 2 Vent = 0...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: txtSize = 3 text = 1 fPanel = 1 Round = 3.1 Width = 90 bShell = 0 m = 0.6 tShell = 0 Length = 140 Police = Arial Black Height = 50 txt =...
thingiverse
This is a personalized version of http://www.thingiverse.com/thing:307267, designed using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=307267. The model features visible windows and bricks, excludes a door, has three...
thingiverse
This is an updated version to ensure the audio controls remain accessible and the additional USB connection remains functional.
thingiverse
NZXT H510i - Essential Component for Enhanced Airflow of 120mm Front Fan \r\nAdditional upgrades will follow suit.
thingiverse
... the top and bottom).I can't over-stress this, do not over-tighten the screws. No uga dugas needed.Printed with PLA.Infill: 40%Fill Pattern: GridPerimeters: 3Tinkercad link:https://www.tinkercad.com/things/5EjStLRqmzW-nzxt-front-fan-mounts-h210-h210i
thingiverse
This is a project to mount two 120x120x15mm or 140x140x15mm fans to the back of the NZXT H1 case. The perforated back panel is the native one. This project is a remix of https://www.thingiverse.com/thing:4716763 The latches are printed separately...
thingiverse
I designed a sensor panel holder for the H210. Might work with the H510 and H710 too. ...The sensor panel is a samsung Galaxy S3.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=49590 Instructions Using the following options: left_port2_custom_circle_radius = 0 back_port3_custom_circle_radius = 0 back_port5_custom_rectangle_width = 0 front_port2_custom_circle_radius = 0...