nzxt h510 front panel replacement 3d models

The reason for creating this is because I noticed that the NZXT H510 Elite has terrible airflow. ...I created this spacer to open the front panel slightly enough to increase airflow and not disturbed the aesthetic of a closed glass case. ...Enjoy.

For the inside pieces I used 2 walls, 0 bottom and top layers 30% cubic subdivision for the pattern (pick whatever you like) I did the hole with the grinder and its dimensions are 160x300mm

I use superglue to assemble ill add a picture so you can see where everything goes I use 10x1mm magnets I got on amazon and you can buy a mesh filter and cut it to size for some case filtration.

I had my GPU positioned vertically, with fans almost brushing against the glass panel. Upon inspecting temps, they soared to 84-85C on my GPU after just five minutes. So incorporating this modification appears to reduce the temp to around 80C. I...

RaspberryPi case that looks like the NZXT H510. Use a small piece of plexiglass or clear plastic for the side panel. Compatible with some heat pipe with fan coolers out there. ...Use a 16mm Pushbutton switch for the power button.

This is for a video. ...https://youtu.be/NaTBuYsSpjU Made for NZXT H510

Casefanholder 120mm for extra Fans on the bottom of your NZXT H510 Elite Case

shorter feet for the NZXT H510. may also fit H500 but can't confirm it. "ohne" version with flat bottom and one with indented bottom Print with support. ...(x/y dist ~0.8mm)

One of my H510's foot was broken so i remade it in a stronger version on the parts that broke. ... You need to keep the screw and the rubber pad that was installed with the old one, you can just glue it on the 3D print.

This wall mount is designed specifically for the NZXT H510 Elite case, but its compact size suggests that it may also work with other NZXT enclosures. ...The mounting bracket measures a generous 215 millimeters in width, allowing for easy installation...

It was designed for my specific setup but it should be able to fit into many rigs with minor adjustments to the height and foot, although I would recommend it particularly for use with the NZXT H510 Elite as the case has a cable managing bracket the...

Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...

I ordered a custom front panel for the NZXT H210i from JakefaceCustoms on Etsy. https://www.etsy.com/shop/JakefaceCustoms Love the front cover, but the way it is designed and attaches, it leaves a gap at the top which kind of bothered me. ...So I...

It fits for NZXT H7 Flow. ...Maybe for other NZXT models too.

This is a stand for NZXT H510 case

My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. ...Air filters coming soon.

<p>The magnets used are 6mm X 1mm</p><p>Printed face down and superglue together</p><p>I have added the f3d,step and 3mf files</p><p>Hope it helps</p>

just a mount designed with 3080ti for the NZXT H510

that filter would be completely useless so might as well repurpose it for the front side.instructions are on the Picture, it's self explanatory.also, the Mounting Brackets is for 140mm Fans, cause who would use 120 on an h7 elite you monster - 3 -to...

Panel is made from 9 main parts and "hardware" like pins and handles You will need 4 long and 4 short pins and couple handles (there are 14 holes but I haven't tested how many will be needed). It would be good to print samples of hardware to test...

a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.

a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.

Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.

A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the...

A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet.Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the case...

One of mine UPS hit the ground and broke front panel. I decided to prepare replacement. If you own that kind of UPS you should be interested.</p> <p>You may choose to print version with or without our logo. ...Enjoy!</p> <h3>Print...

Tronxy Prusa i3 printer owners quickly find that installing a new front panel is essential for repairing their machine on a sturdy base plate.

One of my UPS units crashed to the floor and shattered its front panel. I have made up my mind to build a brand new one. If you possess this type of UPS, you definitely will want to know about it.\r\n\r\nYou can opt for a printed version with or...

I replaced the car's radio with a custom-made display that shows the charging current from my 2x185w solar panels. The road noise and engine whine of the ZAP/XEBRA Electric car are so loud that they completely overpower any sound coming from the...

I measure a broken panel in one of my drawers and instead of getting wood, I take charge like a man with a plan using tools to create a 3D model. Then I cut it into pieces that can be easily assembled for smaller printers. This might seem useless to...