nzxt h510 elite mesh front panel 3d models
283290 3d models found related to nzxt h510 elite mesh front panel.
thingiverse
I use superglue to assemble ill add a picture so you can see where everything goes I use 10x1mm magnets I got on amazon and you can buy a mesh filter and cut it to size for some case filtration.
thingiverse
The reason for creating this is because I noticed that the NZXT H510 Elite has terrible airflow. I created this spacer to open the front panel slightly enough to increase airflow and not disturbed the aesthetic of a closed glass case. ...Enjoy.
thingiverse
My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. ...Air filters coming soon.
thingiverse
I had my GPU positioned vertically, with fans almost brushing against the glass panel. Upon inspecting temps, they soared to 84-85C on my GPU after just five minutes. So incorporating this modification appears to reduce the temp to around 80C. I...
thingiverse
For the inside pieces I used 2 walls, 0 bottom and top layers 30% cubic subdivision for the pattern (pick whatever you like) I did the hole with the grinder and its dimensions are 160x300mm
thingiverse
This wall mount is designed specifically for the NZXT H510 Elite case, but its compact size suggests that it may also work with other NZXT enclosures. ...The mounting bracket measures a generous 215 millimeters in width, allowing for easy installation...
myminifactory
It was designed for my specific setup but it should be able to fit into many rigs with minor adjustments to the height and foot, although I would recommend it particularly for use with the NZXT H510 Elite as the case has a cable managing bracket the...
prusaprinters
that filter would be completely useless so might as well repurpose it for the front side.instructions are on the Picture, it's self explanatory.also, the Mounting Brackets is for 140mm Fans, cause who would use 120 on an h7 elite you monster - 3 -to...
thingiverse
Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.
thingiverse
Panel is made from 9 main parts and "hardware" like pins and handles You will need 4 long and 4 short pins and couple handles (there are 14 holes but I haven't tested how many will be needed). It would be good to print samples of hardware to test...
thingiverse
This is a custom drive mount designed specifically for the NZXT H500 case. Initially, its purpose was to minimize vibrations and noise from my hard drive, but unfortunately, it did not deliver on those expectations. ...I'm sharing it with you in the...
thingiverse
Casefanholder 120mm for extra Fans on the bottom of your NZXT H510 Elite Case
prusaprinters
RaspberryPi case that looks like the NZXT H510. Use a small piece of plexiglass or clear plastic for the side panel. Compatible with some heat pipe with fan coolers out there. ...Use a 16mm Pushbutton switch for the power button.
thingiverse
This is for a video. ...https://youtu.be/NaTBuYsSpjU Made for NZXT H510
thingiverse
shorter feet for the NZXT H510. may also fit H500 but can't confirm it. "ohne" version with flat bottom and one with indented bottom Print with support. ...(x/y dist ~0.8mm)
thingiverse
One of my H510's foot was broken so i remade it in a stronger version on the parts that broke. ... You need to keep the screw and the rubber pad that was installed with the old one, you can just glue it on the 3D print.
thingiverse
PLEASE NOTE: This is a modification of one component from another project, therefore not a complete ready to be printed project. ...Visit this link to download the rest of the required components: https://www.thingiverse.com/thing:5213417 ...
thingiverse
Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...
cults3d
As shown gpu support bracket to help stop video card sag
thingiverse
I ordered a custom front panel for the NZXT H210i from JakefaceCustoms on Etsy. https://www.etsy.com/shop/JakefaceCustoms Love the front cover, but the way it is designed and attaches, it leaves a gap at the top which kind of bothered me. ...So I...
thingiverse
It fits for NZXT H7 Flow. ...Maybe for other NZXT models too.
thingiverse
Made to impove the airflow through restricted PC case front panels. I made these for a Case Upgrade Video on my YouTube Channel "PXL Generator" Watch it here. ... English - https://www.youtube.com/watch?v=B4DF482Tvio Deutsch -...
prusaprinters
<p>The magnets used are 6mm X 1mm</p><p>Printed face down and superglue together</p><p>I have added the f3d,step and 3mf files</p><p>Hope it helps</p>
thingiverse
NZXT H7 Elite Front Panel Spacer ========================== This is a 2 parts Spacer for the NZXT H7 Elite computer case. You will be able to reuse the snapping part and the 2 screws from your NZXT case. It help drastically with the noise and the...
thingiverse
just a mount designed with 3080ti for the NZXT H510
thingiverse
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
cults3d
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the...
prusaprinters
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet.Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the case...