nzxt h1 upgrades 3d models

Replacement fan grill for NZXT H1 radiator fan or really any 140mm fan. ...Just in case you accidentally send yours back to NZXT during RMA.

3D model for NZXT H1 computer case, front and back panels. Each panel is composed of a frame and a plate. Usefull for modding. ...Measurements should be accurate within +/- 1mm.

A fan cover for 120mm fans for the NZXT H1 case. Used for the back of the case. Can be screwed with 3,5 mm x 25 mm screws. ...Between the cover and the fan, there is a gap of 5 mm for dustfilters.

A little riser for my NZXT H1 V2 Case, so the cables have some more room. I´ve got the measurments from the case itself. There is an indent for better getting the front panel down The outsides are (front) 195 x (sides) 197 x (height) 26 mm. It is...

A Remix of NZXT H1 lcd Panel for the 4 inch HDMI IPS Touchscreen 800 * 480 on Amazon LCD Panel https://www.amazon.de/Waveshare-4inch-LCD-HDMI-Resolution/dp/B07QK89X53?ref_=ast_sto_dp&th=1&psc=1 HDMI Cable...

I wanted a bracket so I could mount fans in the back of my NZXT H1 case without them being visible while still being able to use the exiting back panel. Since I couldn't find anything quite what I wanted I designed my own. This should work for...

I wanted a bracket so I could mount fans in the back of my NZXT H1 case without them being visible while still being able to use the exiting back panel. Since I couldn't find anything quite what I wanted I designed my own.</p> <p>This should work for...

***Updates*** - 2020-11-23 - added `nzxt-140-mesh-circle-v2.stl` new version with round holes matching original design ***NZXT back replacement*** Replacement for backpanel with mounting for 2 140mm fans ***Mounting ball*** This are for being able to...

NZXT H1 Backpanel extending bracket to house 15mm fans inside the case.

This is a adapter for the top power button of the NZXT H1 case that has been inverted (upside down) With this adapter you can attach the power button connector to the chassis with a perfect alligment.

This is a remix of https://www.thingiverse.com/thing:4883292 to allow it to fit in the front of NZXT H1. The pins are for the bottom of the 3d prints and will hold for the front. The new files have cut outs to fit. ...

This is a custom Power Supply Cover designed specifically for the NZXT H1 computer case. You should print this item at a layer height of 15mm using a nozzle diameter of 0.4mm, and be sure to add a support under the two top clips as they tend to...

I recently got the NZXT H1 and put my main rig into it, because I needed more desk space to put all my 3D prints.&nbsp;Of course in such a small case, temps are always an issue, especcially when gaming. ...I had two Noctua NF-P12 lying around and...

3) Squared off the sides panel flush with NZXT sides while still having the original slope to fit easier. 4) Removed the screw mounting mechanism for both the top left and right and bottom left and right panel. 5) Filled in the gap side gaps...

This is an upgrade or replacement kit for mounting my [NZXT H1 Custom panel](https://eigakai.ro/industrial-design/nzxt-h1-custom-panels). It uses pegs which fit into the original mounts, just like the TG panel. The corner guides are used to...

Dual 40mm Exhaust Fan Shroud for NZXT H1 Case. Both fans sit securely within the shroud, held firmly in place by double-sided tape that attaches directly to the case itself. ... V3: A significant upgrade has been made with the addition of a center...

Remixed for use with "NZXT H1 rear panel for 15mm / 25mm fans" Use heatset m3 inserts and screw in the more durable snap pins. Enjoy! ... Required Materials: 4x M3x10mm screws 4x m3 Heat set inserts

With this mod you can simply add a 80mm fan to your NZXT H1 V1 (the one without the fan). You will lose a lot of GPU-space, also you have to cut the case for this. ...

One of my systems was based on a NZXT H1 V2. After buying a NZX H1 V2 i wanted the extra fan in my V1 also. After a bit of tinkering and cutting i created a Holder that uses the Holes from the original HDD cage. ...That means: - You have to cut your...

A display cover mod for the NZXT H1 power supply cover for a 4 inch display. ... Display used: https://www.amazon.de/dp/B07XFYXD2V/ref=cm_sw_em_r_mt_dp_mL22FbF1C4VZ5?_encoding=UTF8&psc=1 HDMI 90° angel: ...

Triple 40mm Exhaust Fan Shroud for NZXT H1 Case. Both sides should be secured to the case using double-sided tape. Note: The bottom fan position is not suitable for a 20mm fan, as the GPU bracket will obstruct it. However, standard 10mm deep fans...

Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. ...

Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. If...

Rather than replacing my entire front panel on my NZXT H1 I designed some spacers to help provide a bit of an air gap to facilitate more airflow. I have a couple of 120mm fans on the back of the case that pull air though when the GPU gets toasty. If...

Inspired by some of the LCD mods on Reddit/SFFPC for the NZXT, I gave this LCD mod a crack and it worked out pretty well.You need the 3 prints.. ...one's the back plate, and two brackets to hold the screen in place.</p><p>The screen i used was this...

Call it irony, but I designed this before Christmas just to see that you printed one of my NZXT designs! This is a remix that allows for a 15mm slim fan (the Noctua one to be exact) Would also like to note: this is remixed from the v1 files, but I...

... corner with recess for the foot pads for a bit more stability. Pic shows a little torch behind, would be good to remix this for an RGB strip too I think, or print in a clear filament too! Might also work with the v2 as it is just a PSU upgrade?

Just my design of an NZXT H1 Power Supply Cover for a 3.5 Inch Raspberry Pi Display

The original Pins seemed too loose. User awolf375 mentioned in the comments that the diameter of the ball should be 6.65mm. I used Tinkercad to create a basic ball & cylinder shape to match the original Pins. These fit better and more securely. ...Print...

This is a remix from 365lyf lcd power supply cover. The LCD screen that I used is from this link. You need HDMI cable as well micro USB for the power supply. LCD panel: https://a.aliexpress.com/_mNpSrBr Ordered the 4inch for rpi4. ... Hdmi cable:...