nzxt h1 fan bracket 3d models

I wanted a bracket so I could mount fans in the back of my NZXT H1 case without them being visible while still being able to use the exiting back panel. Since I couldn't find anything quite what I wanted I designed my own. This should work for 140mm...

I wanted a bracket so I could mount fans in the back of my NZXT H1 case without them being visible while still being able to use the exiting back panel. Since I couldn't find anything quite what I wanted I designed my own. This should work for 140mm...

3) Squared off the sides panel flush with NZXT sides while still having the original slope to fit easier. 4) Removed the screw mounting mechanism for both the top left and right and bottom left and right panel. 5) Filled in the gap side gaps...

Replacement fan grill for NZXT H1 radiator fan or really any 140mm fan. ...Just in case you accidentally send yours back to NZXT during RMA.

A fan cover for 120mm fans for the NZXT H1 case. Used for the back of the case. Can be screwed with 3,5 mm x 25 mm screws. ...Between the cover and the fan, there is a gap of 5 mm for dustfilters.

***Updates*** - 2020-11-23 - added `nzxt-140-mesh-circle-v2.stl` new version with round holes matching original design ***NZXT back replacement*** Replacement for backpanel with mounting for 2 140mm fans ***Mounting ball*** This are for being able to...

NZXT H1 Backpanel extending bracket to house 15mm fans inside the case.

I recently got the NZXT H1 and put my main rig into it, because I needed more desk space to put all my 3D prints. Of course in such a small case, temps are always an issue, especcially when gaming. ...I had two Noctua NF-P12 lying around and...

This is a remix of https://www.thingiverse.com/thing:4883292 to allow it to fit in the front of NZXT H1. The pins are for the bottom of the 3d prints and will hold for the front. The new files have cut outs to fit. ...

With this mod you can simply add a 80mm fan to your NZXT H1 V1 (the one without the fan). You will lose a lot of GPU-space, also you have to cut the case for this. ...

After buying a NZX H1 V2 i wanted the extra fan in my V1 also. After a bit of tinkering and cutting i created a Holder that uses the Holes from the original HDD cage. ...That means: - You have to cut your case - You will lose GPU clearance - You...

This is a remix that allows for a 15mm slim fan (the Noctua one to be exact) Would also like to note: this is remixed from the v1 files, but I have made it so that the spacers fit perfectly on the ball joint and the ball joint on the spacer is a...

I split the original single piece design to be printer on my Ender 3 Pro. ...I also enlarged the mesh for the fans. ...You will still nee the "clip on ball" object from the original design.

I needed my existing 4TB HGST hard drive mounted securely inside the NZXT H1 but didn't want to drill holes onto the case. Materials: x4 3.5 inch hdd screws [reuse] x2 original screws from the 2.5 inch hdd caddy [optional] x2 power supply...

Needed a solid hdd bracket even if it required a bit more material. Voila. ...Updated to be in mm.

3D model for NZXT H1 computer case, front and back panels. Each panel is composed of a frame and a plate. Usefull for modding. ...Measurements should be accurate within +/- 1mm.

A little riser for my NZXT H1 V2 Case, so the cables have some more room. I´ve got the measurments from the case itself. There is an indent for better getting the front panel down The outsides are (front) 195 x (sides) 197 x (height) 26 mm. It is...

A Remix of NZXT H1 lcd Panel for the 4 inch HDMI IPS Touchscreen 800 * 480 on Amazon LCD Panel https://www.amazon.de/Waveshare-4inch-LCD-HDMI-Resolution/dp/B07QK89X53?ref_=ast_sto_dp&th=1&psc=1 HDMI Cable...

Triple 40mm Exhaust Fan Shroud for NZXT H1 Case. Both sides should be secured to the case using double-sided tape. Note: The bottom fan position is not suitable for a 20mm fan, as the GPU bracket will obstruct it. However, standard 10mm deep fans...

Dual 40mm Exhaust Fan Shroud for NZXT H1 Case. Both fans sit securely within the shroud, held firmly in place by double-sided tape that attaches directly to the case itself. ... V3: A significant upgrade has been made with the addition of a center...

Remix of https://www.thingiverse.com/thing:4513135, just a little shorter so that it's possible to use three A4x20 fans (doesn't bump into the GPU bracket on the bottom).

I designed this bracket to be able to install a 3.5" HDD drive in addition to one 2.5" SSD into my NZXT H1 v1 PC case. Just remove the original 2x SSD bracket and use my bracket instead. You will need some 90° angeled SATA connectors to connect the...

I designed this bracket to be able to install a 3.5" HDD drive in addition to one 2.5" SSD into my NZXT H1 v1 PC case. Just remove the original 2x SSD bracket and use my bracket instead. You will need some 90° angeled SATA connectors to connect the...

This is a adapter for the top power button of the NZXT H1 case that has been inverted (upside down) With this adapter you can attach the power button connector to the chassis with a perfect alligment.

This is a custom Power Supply Cover designed specifically for the NZXT H1 computer case. You should print this item at a layer height of 15mm using a nozzle diameter of 0.4mm, and be sure to add a support under the two top clips as they tend to...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

<p>Comes in 4 pieces, split STL to objects in prusa slicer. There's a 0.5mm gap between parts; mask back panel, snap pieces into back panel, and fill gaps w/ JB-Weld or similar. This is to allow everything to fit on the bed and account for tolerance...

Remixed for use with "NZXT H1 rear panel for 15mm / 25mm fans" Use heatset m3 inserts and screw in the more durable snap pins. Enjoy! ... Required Materials: 4x M3x10mm screws 4x m3 Heat set inserts

As printed by hundreds of H1 owners on Reddit, I present the:Triple &amp; Dual 40mm Exhaust Fan Shrouds for NZXT H1 Case - Version 4.0Benefits:Typically a 6 degree Celsius drop on RTX series GPUS with three fan versionAdditional 2-6 degree drop...

This is a project to mount two 120x120x15mm or 140x140x15mm fans to the back of the NZXT H1 case. The perforated back panel is the native one. This project is a remix of https://www.thingiverse.com/thing:4716763 The latches are printed separately...