nzxt case mods 3d models

Things Required After Printing: * 3mm Acrylic Sheets * 1/2-Inch Magnets * Gel Super Glue * Screws with Washers * Acrylic Cutting Tools I Utilized the Original Mounting Points on the Front Panel to Attach the New Mounts.

Hey everyone, I've created a custom modification for my NZXT case that enhances airflow. If you're interested in making the same upgrade, feel free to follow along. To get started, simply cut out a panel with dimensions of 38.5 x 14.5 and print the...

SSD Bracket to add more hard drives to a NZXT M59 Case. You will need to print x2 Brackets and 4 screws per SSD/HDD. ... The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.

SSD Bracket to add more hard drives to a NZXT M59 Case. ...You will need to print x2 Brackets and 4 screws per SSD/HDD.</p> <p>The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket.</p>...

Similar to my EKWB pump / res combo holder: https://www.printables.com/model/291904-ek-pump-holder-for-nzxt-casesThis mounts the Alphacool Eisstation to the vertical bar inside NZXT's PC cases.

Made a small hook, to place my cords on the side of the case.Its designed for the holes in the NZXT H710 Case.

NZXT Case for Raspberry Pi. Will fit more other Pi's but check. Top is glued on. Rings are pressed in, very tight. Perhaps print them 99% in all dimensions. Bar is also pretty tight. ... Snaps in.

# ## Italiano: ## Questo logo é all'interno di tutti i computer di NZXT. Esso ha una dimensione standard e quindi é adatto a tutti i case. Dimensioni: Larghezza 85mm Altezza 22mm Qualsiasi commento o suggerimento è ben accetto. ## English:...

Blank mini NZXT case design I have created. Change size of model to at least 150% in your slicer for recommended detail. Size larger then 150% will also work. Must Print with supports inside for pipes to print properly. ...Removing supports between...

This replacement spring latch is designed specifically for NZXT Phantom computer cases, but mine snapped and spare parts are unlikely to be available. The part was created using Fusion 360 software and printed on a Prusa Mini 3D printer. ...Installing...

Considering temperature variations will occur depending on individual cases, I strongly suggest printing one before making all four to ensure a snug fit. If your rubber feet are slightly oversized like mine, you may want to upscale the model by...

This is a stand for NZXT H510 case

this is a mount for the corsair commander controller. ...it is designed to fit the ssd mount in the nzxt H510i case.

This is a 5.25/optical bay cover for an old 2004-era NZXT PC Case. I got the case 2nd hand, and wanted to fill up the empty bays for dust and airflow reasons. ...Enjoy.

LED strip mount for NZXT 510 flow case. Might work with their other cases too but not sure. I used glue to attach the led strip to the mount but could also use double sided tape. ...This replaces the parts in the case where the glass snaps into just...

Modified the original controller hook to slide right onto the front of NZXT's S340 PC case, should hold any Xbox/Playstation controller. ... I recommend making the entire hook skinnier/wider based on the controller you use, to make it harder for the...

I attempted to print one of those NZXT H440 headphone holders, but it didn't fit my case perfectly. I decided to take matters into my own hands and design a custom solution that would work seamlessly with my setup. ...The front of my case is 16mm thick...

This holder ist designed for the NZXT Case, because there is a hole in its "bottom" where the holder can fit in. On its top, of the holder, it just has contact to the 2x8pin connectors. ...The version I uploaded is slightly different, I fixed some...

This innovative holder is specifically tailored for the NZXT Case, which boasts a clever design feature: a hole in its bottom that perfectly accommodates the holder. On top of the holder, you'll find two convenient 2x8pin connectors that make...

This is my debut design - a versatile holder designed to accommodate a headset that can be used with any case or placed on top of a table.

Align the foot to the case so the little slot is inward, toward the filter, and push it onto the case guided by the locator pins. Tighten the #6-32 screwSecure a caster to the foot using provided screws no longer than 9/16" (14.3mm) or you'll hit the...

Some my mods for Deepcool Tesseract PC case. Includes: - New legs for case to make PSU fan higher off the floor (and make it prettier, of course :) - PSU cover that hides long and unused cables - Bracket for mounting liquid cooler radiator under...

(unfortunately no longer available here on thingiverse, excellent mods for Ammo_mikes bullet collator) I designed it to use cheap 14mm outer diameter (1mm wire diameter) extension spring from Aliexpress, such as...

Mini NZXT h500 case for raspberry pi model 4 Video Link: https://youtu.be/3GUH698xS0k

I'm sharing a straightforward headphone holder designed to fit snugly into the front hole of the NZXT S340 case. As a newcomer to public design, I'm proud to share this simple yet practical solution. ...Whether or not you own an S340 tower, I believe...

... the right size for love nore money. Old nzxt case we got second hand for a tenner. all other parts for new computer already ordered, thought what the heck, i got high temp tough plastic, see if it works. It works. ... you need it, here it is.

This adapter allows you to secure the Vive connector box within an empty drive bay on a NZXT Switch case. The design isn't flawless and I would approach it differently if I were to rework it. Its compatibility may extend beyond this specific setup,...

A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the...

A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet.Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks under the case...

I've created custom covers for SSDs that fit perfectly into NZXT PC cases. If you'd like, I can provide the data needed to clip any other design into a CAD format - just let me know what you're looking for! The base model is called SSD_Cover_Base...