nylock mod prusa mk3s 3d models

It doubles back at the far end to run parallel to itself on the other side of the bar. The switch clips have the small end inserted into the frame groove, and stay in place when rotated 90 degrees so they are upright as shown in the photos. Print...

Hi, i had the Problem, that after printing the Bear Extruder Body, the 8mm steel ball will not fit in it's place. So i used a 8,5mm drill bit and correct that issue. After that you get a huge hole in that body and maybe the filament sensor have...

The back dump basket is bigger, improved clip for the frame (doesn't sag), with and without branding, better allen key (small tool) holder, raised and moved the hooks to better positions, more small basket slots, more and varried holes, two...

This is a remix from the project https://www.prusaprinters.org/prints/39449.The goal was to mount an Raspberry Pi 4 directly on the frame of the Prusa i3 MK3S+ a look alike.As per previous made version the case is small and as compact as...

I got a Prusa MK3S+ a few weeks back and wanted to try out and make some 3D models my self to print and learn a bit about 3d modelling and connectors etc.. And since I had some LED strip laying around I went ahead and created a rail / holder that can...

The goal was to mount an Raspberry Pi 4 directly on the frame of the Prusa i3 MK3S+ a look alike. As per previous made version the case is small and as compact as possible. Main change is the new opening for the DSI connector of the Pi allowing...

This is a frame-mounted camera bracket for Prusa MK3s that integrates a Raspberry Pi 3 B+ Case. It screws into the holes where the LCD is normally placed, providing the strongest direct frame connection and the best front-facing position for...

This is an updated design for use with MK3s, eliminating the need to remove the fan. The mounting system has been tailored specifically for the Endurance 10W Laser module. ...A STEP file has also been included, allowing users to easily modify and apply...

... doesn't sit flush with the rest of the assembly. ... I updated the fs-cover part to create a 1.3mm cutout for the adapter-printer so it sits and screws in better. See Step 35: https://help.prusa3d.com/en/guide/3b-mk3s-extruder-upgrade_186842

Bracket for Mounting PSU to Leg of the Lack Enclosure. ...Crafted with Openscad for the I3 Mk3s (Black) PSU. ... Should Be a Tight Slip Fit for Both PSU and Lack Leg, But No Guarantees Can Be Made for Your Specific Setup.

This is a box that fits under the MK3S and fits in the extrusions. ...It takes some force to get it in but it is secure and can securely hold a lot of tools without interfering with the printer.</p> <p>PETG is best but PLA would probably work</p>

Consider adding a PSU frame specifically designed for the mk3s. Since the PSU can't handle high temperatures, it's best to locate it outside the enclosure. To make the frame sturdier after removing the PSU, print this part and place it at its...

Just an simple conversion from the new Original Extruder Cover for the MK3s+ / MMU2S.Printed in PETG @ 25% infill.The PTFE Tube can reach the end from the extruder, it is easier to mount the filament.No more Loading issues.

Just modified it to be like the MK3s using Fusion 360. This version has the option to tighten the belt by rotating the motor. ... I also added tiny holes for endstop switch that you can to drill to get bigger holes.

There are three heights (Short, Medium, &amp; Tall) and two lengths (Close &amp; Far).Short-Close (SC):&nbsp;C270 Camera - Prusa MK3 Arm-SC.stlC270 Camera - Prusa Bear Arm-SC.stlMedum-Close (MC):&nbsp;C270 Camera - Prusa MK3 Arm-SC.stlC270 Camera -...

When upgrading my Prusa i3 MK2S clone to a MK2.5S, I realized the original Prusa print fan support (for the upper mount on the extruder for the part cooling fan) would not work, because the stepper motors I am using have a connector that must be...

It's a modified and repaired Prusa design that needs to be completely redesigned, but this will serve as a working solution for now. V1.0. Enjoy! Note: This printhead requires a long groove mount addon for Nova. ... <a...

This is a model for a quick-change system of the printhead for the original Prusa printhead and a four axis printhead with rotatable Nozzle.

I am not finding anywhere a PSU holder for Prusa 24V for the left site of the Ikea Lack enclosure. ...have fun with Printing!

Yet another cable chain. Prepared for heated bed cable management Optimized for smooth & quiet movement and simple gathering For more check out the link to [videos of assembly](https://photos.app.goo.gl/eHygWbeXvfq8H6HfA) Important! *...

Many of the guides I tried did not fit well on the frame, so I designed this one from several other designs. ...It is easily attached to the frame, but it is firmly attached!

<p>I like the design but need it more longer and stable. ...:)</p>

It's specifically designed not to wiggle, as pre-existing LCD cable clips for the MK3(S) did and thus were unsatisfactory to me. The opening of the "hook" should point down for a clean look and easy insertion of the LCD-cable. If this helps you out,...

<p>I just remixed this great design so that it uses all the available space. The original design would slide rearward during use, allowing stuff to more easily fall between the resulting gap. In the end, I was able to get mine 18mm longer than the...

... did NOT include the retract at the end of the print to clear the nozzle to unscrew. The nozzle diameter check was also removed since the stock mk3s+ firmware doesnt show the 0.15mm nozzle. ...So double check if you have installed the correct nozzle.

I just completed my enclosure and wanted all the electronics outside of it so I designed this layout without moving the EINSI motherboard away from the MK3S while cooling it with a 92.5mm PC fan.\r\n\r\nTo keep cables organized, I added extensions...

this is updated to fit the MK3S+ upgrade to be able to connect to the palette 2. the Bowden tube is secured in the plastic part with a rubber gourmet. (rubber gourmet dimensions are :center diam. 4.5mm, thickness 5mm, the bottom and top...

I really liked JSund's camera mount for the MK3S but wanted my camera mounted in the front, after some trial and error in Blender I was able to adjust the height and length to what I wanted to be in front but still clear the build plate at full...

Original design, tested with MK3S+MMU2S. It's fantastic, but the filament cooler can't be inserted into the idler; it needs to rotate! I just cut a piece of this part off. For the extruder cooler, I took out the back for weight loss and let my...