number 2 to print 3d models

"Prime or Not!" is an entertaining and interactive game that teaches kids about prime numbers while allowing them to explore and play with these concepts. This resource serves as a learning tool, helping children memorize, understand, and verify...

Needed a new house number, printed one. On Grabcad I have the fusion model that you can edit. Print instructionsLicence: Creative Commons - Attribution - Non-Commercial Category: Outdoor & Garden Print Settings Rafts: Yes Supports: No Notes: Big...

This is Number blocks 1bbb from the kids cartoon I printed with 10% infill and its more than enough. ...will print fine without supports as they are only needed for under the mouth and eye so I used the experimental setting in cura: Make overhang...

... designed by SjorsZuidema on Thingiverse. ...Printed starting from the HDMI end moving towards the Gardena end, note that there is still some overhang near the top which can be resolved using a rubber ring similar to an official Gardena connector.

Adapter to mount a Wahoo Computer on any Garmin mount. ...Not testet for Garmin Computer on Wahoo mount but i think that is possible.

By changing the variables where it says to, you can customize the following: -Button diameter -Button thickness -Number of holes in the button -Diameter of holes in the button -Spacing between the holes in the button -Making the button concave in the...

This adapter spacer frame is essential if you want to fit the Chinese Ultimaker 2+ feeder to the Ultimaker 2, as some stepper shafts are too long on certain Ultimaker 2 models. Instead of cutting the shaft, which can be a bad idea, use this adapter...

... connects G 1" hoses to larger G 2" outlets, accommodating a diameter of 59.61mm. Meanwhile, the second adapter provides a smooth transition from G 1" hoses to G 1 1/2" fittings, offering a diameter of 47.8mm for optimal gardening performance.

Using the Following Options: double double Rod Height (D): 31 Bar to rod nut gap: 3.6 Rod thread depth for gopro_bar_screw_nut_d: 2.4 Gopro Bar Thread Diameter (A): 3.2 Gopro captive Rod ID (H) diameter with angle 45 and primary = double,...

120mm fan to 75mm x 2. Used in my boat to distribute heat in the boat. Used in combination with my other design 75mm to 120mm fan. ... I would NOT recommend printing in other materials than ABS or materials with similar heat carateristics.

Centering rings for the Estes Pro Series II 2-inch body tube attach securely to the Estes 29mm motor mount. Print two and join them together, bonding them firmly back to back. Flight tested successfully up to H53 so far. ... The 'anchor' file version...

Using the following options: pane_size = extra_large image_file = updated_lithopane_new20150423-16229-1vxay3-16467.dat picture_shape = irregular text_reverse = yes picture_orientation = vertical text_size = 8 text_line_5 = Congratulations text_line_4...

This model was made so that the strap accessory of Quest 2 can be used on Quest 3.https://youtu.be/BGd2rGTc6MkIt was manufactured with the length in mind so that the power cable can be safely connected to products such as battery straps.It is also...

Pwncnc is committed to empowering our vibrant Makers community, and we're dedicated to connecting you with the resources needed to create and bring your projects to life, including non-printed parts and other essential items, all accessible through...

mounts a cheap sim racing handbrake to 2" thick SCH40 PVC

... version without them. Here are my print settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 50% Notes: You can lower the infill percentage if you prefer, but I recommend using 50% for added stability of the Duplo brick.

Use this 2-D-cell to 18650 converter when you're looking for an affordable alternative to replacing expensive D-cell batteries.

People use a 4-inch to 2-inch PVC pipe reducer. ...The reducer is available in both straight and 11-degree angled configurations.

4" to 2" PVC pipe reducer. Straight and 11° angle models. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Doesn't Matter Resolution: 0.20 Infill: 20-30 Filament: Generic PETG White Notes: Consider increasing perimeters ...

... emergency call... also it was fun little project to make. - Print out of PETG - recommended, or PLA - Put piece of double sided tape around the charging port and stick it to the wall - Put heat shrink over the "discharging" connector soldering pads

Lid for 2" (5cm) vvs pipe, used in my case for vertical growing. ... Place lid on all pipes you are not using, so no extra light get in. Print with the big flat surface down on the bed, then you will not need any support.

Venetoclax binds to the BCL-2 hydrophobic groove through various groups, including a 4-chlorophenyl group attached to the P2 subpocket, a piperazine group bound to the shallower groove between the P2 and P4 pockets, and an azaindole group bound in...

This is a multistage gear reducer based on very simple geometry. ...Each stage has a 2 to 1 reduction ratio. It has very low friction. ... https://youtu.be/KIELf7DNJAk

Housing for the HDMI (out) to CSI-2 converter for Raspberry Pi. This is compatible with my Raspberry Pi 4 case. ...I use this converter casing in conjunction with my Raspberry Pi 4 case.

This is an adapter from quest 1 to quest 2. ...Just make sure you wrap the side with some kind of tape so it stays on and is secure.

This is a 2 to 5 water splitter with tapered push fittings for for soft tubing w/ 3/8" OD, 1/4" ID. Supports are highly recommended. ...This object was made in Tinkercad.

This is an adapter that connects a 1.5 inch wet/dry vac hose to a 2 inch adapter, specifically designed for my Bosch RA1181 Routing Table and compatible with my Ridgid WD06700 Vacuum. The hose from the vacuum attaches on the inside of the large outer...

Takes a standard 80mm fan and converts it to a 2" PVC pipe fitting. Note pipe fitting not pipe, so for instance it will fit inside a 90 coupler, the od of the fitting is the same as 2" pipe. There are no screw mounts as the fan should push fit...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

I designed an adapter that fits perfectly onto the Teflon tube from Palette 2, connecting it directly to a BMG Extruder. ...To assemble it, simply insert the rubber ring into the large opening and then secure it behind the push-fitting ring on the BMG...