nrf52840 dk 3d models
1411 3d models found related to nrf52840 dk.thingiverse
This is a snap-together case for the NRF52840-DK development board. This is the largest board I've designed this style case for, and with my printer size, I was restricted to placing the clasps along the long edge. ...I also had to reduce some of the...
prusaprinters
Minimalistic holder for NRF52840 DK that avoids the awkward stance when laying on a table due to the battery holder underneath. This holder makes it sit flat and easier to plug in usb cables into and genrally nicer to work with. Its worth nothing...
thingiverse
Minimalistic holder for NRF52840 DK that avoids the awkward stance when laying on a table due to the battery holder underneath. This holder makes it sit flat and easier to plug in usb cables into and genrally nicer to work with. Its worth nothing...
thingiverse
Compatible with Nordic Semiconductor nRF52840-DK (Version 5), which has a button cell battery under the USB port. This did not fit the case designed by mitikohalls, so I remixed his design and the DK now fits. ... Has no top to the case.
thingiverse
This is a simple prototype rig I build for the Nordic NRF52840 developer kit board. ... It helps keeps things in place.
thingiverse
This is basically the same as the source prototyping rig, which is very nice. I noticed when using it, though, that the bottom right button (Button 4) caused the board to move around when pressed because there's no screw hole to its right, so I added...
grabcad
This is a model of the Nordic Semiconductor nRF52840 Bluetooth 5.0 Prototyping Development Kit."The nRF52840 DK is a versatile single board development kit for Bluetooth Low Energy, Bluetooth mesh, Thread, Zigbee, 802.15.4, ANT and 2.4 GHz...
thingiverse
Using mitikohalls original design, I've been able to make a sturdy case for the Nordic Semiconductor nRF52840 pca10056 development kit. ...The case has a dedicated reset button and exposes most pins on the board.
thingiverse
This is a case for the nRF52840 Development Kit (PCA10056), following the same idea as in this thing: https://www.thingiverse.com/thing:2538889 by [stellarinnovation](https://www.thingiverse.com/stellarinnovation/about).
prusaprinters
You should preparably do the assembly on a second flat surface which you can flip along with the board.Solder the pogo pins in place.Remove the alignment placeholderInsert an NRF52840 dongle and fit it in place by sliding on an nrf_brace.stl piece...
thingiverse
Keychain enclosure for NRF52840 MDK dongle with USB cap https://wiki.makerdiary.com/nrf52840-mdk-usb-dongle/ Remixed from https://www.thingiverse.com/thing:3749398
thingiverse
An enclosure for the nRF52840 USB-Dongle by Nordic Semiconductor. The bottom side of the PCB can be equipped with a SMT header which is supported now. ... Not modified (still original) is the upper part (lid) from the "OpenSK Enclosure" by...
thingiverse
Case for nRF DK. ... Installation confirmed DK: nRF9160 / nRF5340 / nRF52840
thingiverse
Customized version of https://www.thingiverse.com/thing:2749579 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2749579
thingiverse
Customized version of https://www.thingiverse.com/thing:2749579 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2749579
thingiverse
Customized version of https://www.thingiverse.com/thing:408698 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=408698
thingiverse
Customized version of https://www.thingiverse.com/thing:74322 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=74322
thingiverse
Customized version of http://www.thingiverse.com/thing:188275 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=188275 Instructions Using the following options: Font =...
thingiverse
Customized version of http://www.thingiverse.com/thing:40703 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40703 Instructions Using the following options:...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=249257 Instructions Using the following options: fontWidth = 1.0 outerWidth = 5 fontPercent = 0.85 clipHeight = 2 clipWidth = 20 createWhat = 3 string1 = DK
thingiverse
... have to print your own champagne glass. We will provide the stl file for the glass, then all you have to do is print it. And if it holds the champagne in and looks awesome you can win some fantastic prizes. The champange is provided by deluxlife.dk