nr200p top mounted 3d models

 Since this part will be located at the very top of the enclosure, it is subject to the highest temperatures.If this doesn't fit your brand of PTFE tubing, try scaling up or down in 1% increments.The port may seem to be longer than necessary at first...

You should first put it to the test using an iPad 3, 4 or Air - no back casing necessary - then use 3M mounting tape to attach it firmly to a nearby wall. When attaching, make sure there's enough clearance between the clip and shelf for easy access...

**Table Top Flange Update:** You've revised the table top flange due to issues some users were experiencing with different slicers. **Key Features:** * Custom dry box setup with a unique feeding system * Funnel part helps prevent filament tangles...

This will give you the ability to print TPU from the top of the printer by removing the side slider rails and replacing them with my spool holder modded rails. ...You will still have the ability to slide the lid open and shut without removing the spool...

- Remove two screws from the right side of the screen mount and slide the mirrored frame on, replacing screws as found. - At this point, you should see two frame pieces opposite each other: one moving very little on the left and one sliding mostly...

Details: Motor Support: 2 x 5x30 screws for pulleys 2 smooth pulleys (not like on the image) 1 GT2 20-tooth / 6mm / 5mm axle pulley 2 printed spacers (M5x8 ep1.stl) or not 5 M5x8 screws plus 5 T-nuts (personally, I put the back ones and once in...

A small box that can hang on the top of a mk3/s frame to store things. I built it initially to hold little blobs and scraps of filament that I clean up during a print and don't want to walk to a garbage can for every little piece of junk I get. ...It's...

... battery also takes up valuable real estate. This sleek top plate frees up space to accommodate a larger receiver, with strategically placed cutouts for your battery strap and precisely drilled holes for the XT60 connector and antenna.

... 120mm fans in the top panel.Max GPU length supported: 240mm.The ATX PSU bracket is extremely easy to install. Just mount your ATX Power Supply, remove the front panel of your NR200/NR200P, and secure it to the frame with the included screws. 

This custom spool holder was designed specifically for the ADIMlab Gantry (Old style), but its adaptable design makes it an excellent fit for most printers that rely on aluminum extrusion frames. The holder utilizes two high-performance 806zz...

hair dryer holder

Remixed this hanger with a curve and lots of bezels. ...Also slightly raised.

I had an air cooler that was a tad too tall and if I were to force the TG panel into it, it cant stay on. Or is slightly off slanted which annoyed me. Since I have a CAD software and 3D Printer... Why not just create the plastic that locks the panel...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The team...

During the development of the Cooler Master MasterBox NR200P, we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our users?"The team...

Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P.We are making free to print and modify the design for the clips that hold the paneling of our most beloved ITX enclosure(s)!Lost one? Your product is out of warranty?<br>No problem!...

3 shell, iron the top surface for better look. ...Very easy to print.

This is a straightforward design for a top-mounted sled on FT-5 and FT-6 printers that utilizes the stock PCB. There are two versions, one featuring larger holes suitable for M3 knurled inserts (recommended) and another designed specifically for...

I modified the mounting brackets to allow it to be mounted on top of a 2020 extrusion instead of in-front. ...Using M4 hardware.

I modified the mounting brackets to allow it to be mounted on top of a 2020 extrusion instead of in-front. ...Using M4 hardware.

A top-mounted tea dispenser for bags with 65 mm x 75 mm. Attach the mounting plate with two screws or double sided tape. Use the distance bracket if you want to mount them at the right distance from each other. ... ...

This is my first remix from the CR-6 SE filament guide for top mounted double spooler holder. I`m improved the bottom part and add a filament guide to the end hole, so the filament slides to the extruder. Also i remixed the top part for double...

This versatile guide allows you to utilize filament from either side or a roll mounted on top, giving you maximum flexibility in your 3D printing setup. With its sleek design, it effortlessly guides the filament into the extruder with minimal...

... spool holder that comes with the printer. It mounts to the top using the M3 screws and t-nuts from the handle and original spool hinge, but you will also need a single M3 nut. ... Recommended to print in PETG or something stronger than PLA.

E3D hemera mount for linear rails with 20x20mm hole spacing, 5015 radial fan V1_Mounts Was mount was designed for Ender 3/3 PRO with the 3DFUSED X gantry conversion with MGN12H Carriages (but will fit other printers with the same rail system/setup)...

 This gantry/top rail mounted clip does that.  Its a quick print, very easy to mount/dismount from the gantry and the filament clicks in perfectly. When you are done with one spool just clip it into the filament clip, cut it and load a new filament,...