nr200p top mounted 3d models

Remixed this so it can be mounted on the top bar of my Ender 3, since I have the spools of filament on a shelf above it (and using a direct drive mod). ... This is based on my other remix with tighter tolerances for the roller switch:...

Because it's safer and more stable than mounting it on top of the Z bridge. The filament grinds against the frame when mounted this way, causing under-extrusion. This filament guide is optimized for use with the spool on the control box. Mounts...

... design. **Build Instructions & Essential Components:** - This compact top mounted reel assembly calls for two of these bespoke supports - An adequate supply of 6mm diameter carbon fibre rod, totalling approximately 250 millimetres in length

... There are 2 versions: the tray by itself, or with a "sidesaddle" tool caddy. Sidesaddle remixed from https://www.thingiverse.com/thing:2253349 There is also a separate file for just the sidesaddle, which could be mounted with glue or tape anywhere.

Changed the original design to be top mounted under a shelf instead of back mounted to a wall. All credit should go towards the original designer. __The Mi Handheld Vacuum Cleaner 1C comes with only two head holders integrated to its charger. It...

With Bowden, you can feed it under using a top-mounted extruder (example of Bowden setup is in the picture). The arm can be rotated to one of four positions and is locked in place with an M4 screw that is 10-15mm long. The top piece (Top.stl) can...

I had no idea how to mount the extruder in the empty space about the hot-end assembly, so I designed the top plate to hold them. This made me think of being able to have a spool of filament on top of each upright. For me this makes it so there is...

Here's the link: https://smile.amazon.com/gp/product/B002BBGTK6/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1 To make this top mount spool holder, simply print the bracket as normal. You'll need 4 bearings and their corresponding hubs, along with 8...

With that setup, the spool ended up about two to three inches away from the leg, which meant the filament would have to make an almost ninety-degree turn to feed the extruder motor mounted on top of the frame. So I chose to mount the spool on top...

2021-08-03 - Improved the bottom part Designed for the CR-6 SE, this helps guide the filament from a top mounted spool holder down to the runout sensor. The bottom part fits over the filament runout sensor. The top part snaps onto the top left of...

When the filament is mounted on the control box (which is safer and more stable than mounting it on top of the Z bridge) the filament grinds against the frame and can cause under-extrusion. This filament guide is optimized for use with the spool on...

The spool mount I was previously using, my "Anet A8 Spool Mount" was beginning to sag over time, so rather than re-imagining a design I wasn't all-together pleased with, I opted to use a spool holder design I was pleased with, the "Geeetech I3 Pro C...

......The wheels that came with the original Top Mount Spool Holder were not up to my standards, so I decided to upgrade. To minimize resistance, I use bearings, which are incredibly effective. For under $9, I purchased these amazing bearings from Amazon.

... I designed this for anyone that also downloaded my Top mounted filament spool holder for the :LK5 pro also (https://www.thingiverse.com/thing:5883365). ... The guide slides right in the end of the top tube, and is tight enough to lock in there.

... the top hole. This setup can also be adapted for use with the CR-10. (v#a) has been remixed into a belt holder design. (v3a and v4a) have been reworked from a different mount based on the design found at https://www.thingiverse.com/thing:3489340.

......Since I have top mounted linear rails, the sides of the 2020 were available for mounting, and I moved everything outside to maximize the range of motion on the x-axis for klicky probe placement. Files should already be in the correct orientation.

I appreciate the top-mounted Kossel spool holders I've seen on Thingiverse, but since my extruder is mounted on top and I have some larger-diameter spools like those from Hatchbox, I had to offset my center spindle forward for clearance around my...

Why? When the filament is mounted on the control box (which is safer and more stable than mounting it on top of the Z bridge) the filament grinds against the frame and can cause under-extrusion. This filament guide is optimized for use with the spool...

Has a screw knob to tighten it in position. //----------------------------------------------------------------------------------------------------------// Top mount spool holder, uses 8mm linear rods and bearing. Holds large spools for direct dirve...

To have easy access to the spool I wanted a top-mounted design that could easily lift off even the large spool without having to move the printer. This design support up to 110mm wide spools and as narrow as 5cm. I modified the original design...

I wanted to mount a flashlight on my Nexus Pro, but there were no side rails, so I created my own working off of the top rail. This works on the Nexus Pro picatinny rails via friction fit. It is meant for use with these flashlights: ($14 on Amazon...

(2) M5 washers for under the stepper idlers to keep them from rubbing on the mount (4) M5x8 screws with t-nuts to attach the stepper mount to the frame (4) M4x20 screws with t-nuts for mounting the bearing brackets to the frame (4) M4x6 button head...

I have found that filament guides for top-mounted spools do not fit my CR-10 v2, very well. Some of them fit...passably...well, but most are designed for the Ender series; the runout detector and extruder and, most importantly, the carriage assembly...

I used the shortened versions of the [holder](https://www.thingiverse.com/download:8739737) and [roller](https://cdn.thingiverse.com/assets/a3/15/29/83/17/ROLLER.stl) from [Top Filament Holder 2020 6SE, Ender 3, CR-10,...

Print as-is and insert it into the duplicator i3 by sliding it into place at the top-right corner.

Two parts are required: a support base structure that clips onto the top of the printer and the actual spool holder, which needs four printed units based on the clever design found at https://www.thingiverse.com/thing:2047554. You'll need four 608...

This is a much improved version of my top mounted spool holder for the Anet A8 acrylic framed printer. All the pieces of this model, except for the ones named "Spool_Tube_Joiner.stl" and "A8_SH_Binders.stl" will need to be printed twice, once for...

Jointed Top spool filament guide and extruder guide for 1 simple print. Also changed the bowden end that can be tapped in with a bowden metal connection. ... Happy Printing

... Filament guide - https://www.thingiverse.com/thing:4288768 Spool mount - https://www.thingiverse.com/thing:4459319 Just made a revision to make the spool mount slanted to use gravity to hold the spool in place. ...will post pic when print is done.

I'm using my Gotek in an external case, so I wanted the screen to be on the top for better readability, I also decided to switch to using the Blackberry style trackball so put that on top too, With both of those up there and the trackball also...