nr200 case 3d models

35mm spacer to allow for a radiator, larger PSU etc, to suit a Cooler Master NR200 case. Version 2 now available, includes 280mm radiator option: https://www.thingiverse.com/thing:4725016 Makes use of the existing lid Relocates front I/O (USB ports,...

35mm spacer to allow for a radiator, larger PSU etc, to suit a Cooler Master NR200 case. Version 2 now available, includes 280mm radiator option: https://www.thingiverse.com/thing:4725016 Makes use of the existing lid Relocates front I/O (USB ports,...

The space between the 3090 and the PSU was very tight, so I have made a new mount for the PSU. ... NR200 coolermaster case with a silverstone 850W SFX-l and an EVGA 3090 ftw

35mm spacer to allow for a 240 or 280mm radiator up to 30mm deep, larger PSU etc, to suit a Cooler Master NR200 case. Makes use of the existing lid Relocates front I/O (USB ports, power & reset buttons, 3.5mm jack) Can be fixed to the case via zip...

35mm spacer to allow for a 240 or 280mm radiator up to 30mm deep, larger PSU etc, to suit a Cooler Master NR200 case. Makes use of the existing lid Relocates front I/O (USB ports, power & reset buttons, 3.5mm jack) Can be fixed to the case via zip...

### Summary of the T240R- *Top 240 mm Radiator* mount for the Coolermaster NR200 ITX case. This is a mounting assembly/system mod for the Coolermaster NR200 to mount a full size 240mm radiator with 2 120mm fans to the top of the NR200. This mod uses...

I printed these using PETG on a nice slow speed, nothing special!

3 shell, iron the top surface for better look. ...Very easy to print.

Bracket to mount your XBOX Elite Series 2 controller base/dock/charging station to the front top lip of your front panel. Works for holding or charging. ...Remixed from the file attached to this Thing.

adding an M-ATX to NR200 computer case 2 x top 1 x bottom left 1 x bottom center I found that printing it sideways yielded better results

Untested*** Aim is to allow a 120mm Fan/AIO to fit onto the rear of the NR200 Case using the pre existing 92mm fan mounts

You can use the NR200 case screws to mount the bracket to the case and regular motherboard screws for the motherboard. You may have to remove the case clips to accommodate motherboard depending on height Recommend 100% infill. Looking forward to...

This model snaps into the hole behind the power supply in the NR200 case through which the power supply intakes air. Normally there is a gap between the PSU and the ventilated side panel of the case, which allows the PSU to intake warm air from...

My attempt at a riser for a SFX-L PSU in the coolermaster nr200 case. The stock position makes the cables press the gpu below so this mod raises the power supply up my roughly 1cm This requires 3 more screws. ... I might make another version that...

Made this GPU deshroud for cooler master NR200 case. Im using Strix 1080 but this will most probably work with other GPUs if you just adjust the height. ... Does not need any support.

It should bridge the gap between the C14S fan and the side of the NR200 case. This may improve the cooling of the CPU cooler as it may be able to source cooler air from outside the case. It requires supports which makes the print time take longer....

This is a remix of naturalnetworks 'Cooler Master NR200 Case Top Hat Spacer' I would have added the remix in the proper way but Thingiverse is broken again... This tophat is designed with EK 240 D-RGB AIO in mind, with a rad thickness of 27mm. The...

This is a remix of [naturalnetworks](https://www.thingiverse.com/naturalnetworks) [ 'Cooler Master NR200 Case Top Hat Spacer'](https://www.thingiverse.com/thing:4707763) I would have added the remix in the proper way but Thingiverse is broken...

Bracket used to mount a small water cooling reservoir inside the NR200 case. Designed specifically for the EK-RES X3 150, a standalone reservoir (no pump) that fits inside the NR200. Should fit GPUs up to 295mm long in the vertical orientation (mine...

Bracket used to mount a small water cooling reservoir inside the NR200 case. Designed specifically for the EK-RES X3 150, a standalone reservoir (no pump) that fits inside the NR200. Should fit GPUs up to 295mm long in the vertical orientation (mine...

Bracket used to mount a small water cooling reservoir inside the NR200 case. Designed specifically for the EK-RES X3 150, a standalone reservoir (no pump) that fits inside the NR200. Should fit GPUs up to 295mm long in the vertical orientation (mine...

A very simple stand to support a GPU when mounted vertically in the CoolerMaster NR200 case. Screws onto the PCIE riser card/cable using a M3 nut/bolt. The 'feet' of the stand are positioned to sit in the bottom case rails and provides 55mm...

A very simple stand to support a GPU when mounted vertically in the CoolerMaster NR200 case. Screws onto the PCIE riser card/cable using a M3 nut/bolt. The 'feet' of the stand are positioned to sit in the bottom case rails and provides 55mm...

Replacement Clips for the CoolerMaster NR200 PC Case Side panel Clips. The stock clips are weak and hence the side panels fall off easily, these clips hold the panels significantly more tighter. ... You may need to push at the back of the clip...

This bracket supports the GPU by bolting to the back of the GPU and the bottom of the NR200 case. I designed the bracket for my RX6800 reference, but I think it should also work for the RX6800XT, RX6900 and RX6950XT as they seem to have the same size...

Fan duct to suit a Cooler Master NR200 case. Assists with expelling hot air from the GPU via the top front 120mm fan. Useful for GPUs that exhaust air through the backplate eg Nvidia RTX 3000 series, AMD RX 6000 series. Uses the HDD mounts on the...

A tool-less fan mount peg for slim 15mm thick fans on the Cooler Master NR200 case. The original fan mounts were designed with regular 25mm thick fans, which meant that 15mm fans would dangle loose. I added flat sides to the peg to improve...

Legs for NR200 (NR200P).

This is a remix of my own fan spacer (designed to use the same small footprint as the Noctua NF-A15 itself) to perfectly fit it to the bottom of my CoolerMaster NR200 case. I'm using M4 x 30 screws to mount the fan on top of the spacer and the...

Designed to put 120mm 20mm fan at the bottom of a Cooler Master Nr200 case together with a 3 slot GPU (using a powercolor 6900xt). Acts as a GPU mount to prevent gpu sag as well. Using Noxtua 120mm fans and seems to clear the stock Powercolor 6900xt...