nr200 bottom fans 3d models

Coolermaster NR200 bottom Feet with Fan/Radiator shroud for those who want to install there Fans/Radiator underneath there case. Fan 25mm, Radiator 28mm, 38mm, 45mm & 60mm for those after after the thickest Radiators. this is a similar design to that...

extended replacement feet for NR200, which allow bottomed mounted 120mm x 25mm fans. ...Fans will have about 8mm clearance to the ground

Designed to put 120mm 20mm fan at the bottom of a Cooler Master Nr200 case together with a 3 slot GPU (using a powercolor 6900xt). Acts as a GPU mount to prevent gpu sag as well. Using Noxtua 120mm fans and seems to clear the stock Powercolor 6900xt...

I took DROUGA's design and simply added 10mm to the height so that standard 25mm fans will fit.

I took DROUGA's design and simply added 10mm to the height so that standard 25mm fans will fit.

The original model by tangcla is on Thingiverse, but I reuploaded it here with permission so it can be added to my NR200 parts collection. ...Check my replacement TPU feet model to add to this model.</p><p>Link to original: <a...

NR200 bottom extension for large GPU. Reuses accessories for bottom plate. Metal cutting of the frame is required. 2 M4 screw required to assemble both parts. ... Note : I didn't take time to make the last corrections, there are two missing holes...

A tool-less fan mount peg for slim 15mm thick fans on the Cooler Master NR200 case. The original fan mounts were designed with regular 25mm thick fans, which meant that 15mm fans would dangle loose. I added flat sides to the peg to improve...

GPU Fan shroud for 120mm fans for a deshrouded GPU in a NR200 Base design is for 10mm tall shroud, adjust scaling to fit your use case. ... Step allows for fans to push up against back plate of the case

Remixed specifically for users operating the Twin Fans, this design offers a unique twist on the original fan shroud and endstop mounts. By removing the mounting points for the standard fan shroud and the mounts for an endstop to the right, this...

It should bridge the gap between the C14S fan and the side of the NR200 case. This may improve the cooling of the CPU cooler as it may be able to source cooler air from outside the case. It requires supports which makes the print time take longer....

Was looking to add better airflow by adding some fans in the bottom inside, but restricted for space because I am getting a triple slot GPU in the near future. So I got the idea to add slim 120x17mm fans to the outside and move the dust filter...

Legs for NR200 (NR200P).

This simple bracket allows you to mount up to a 140mm fan near the front of the case. ...Often the radiator bracket included with the NR200 doesn't fit with tower coolers. ...This bracket lets you still use a fan with the maximum height tower coolers.

I designed a bottom plate for my Ender 5 printers after I upgraded the fans with more silent Noctua fans (and had to install 12V converters in the process). As you can see it has fittings for the converters and the fans. I'm relly satisfied with...

NR200 Rear Fan to 140mm External Mount Prototype

I remixed a few things to make this happen: Bottom Panel https://www.thingiverse.com/thing:3864094 Electronics (Front) side fan with buckconverter holder. https://www.thingiverse.com/thing:4612023 Power Supply (Back) side ...

Donations: https://paypal.me/danhil Complete bottom cover replacement to install two 80cm silent fans. The two PSU cover will be fixated by using the lock fixed with super glue after sticking the connectors together. The original cover of the PSU...

Enhanced Power Supply Mounting System Designed Specifically for Use with 120mm Fans and Optimized Heat Dissipation Performance.

The fan can be mounted with normal case fan screws from the boardside. The 2 original frontscrews can be used, the backside can be screwed with a profile on the 40 with a profile nut. Cables you want to route to the side can be zipped to the...

Untested*** Aim is to allow a 120mm Fan/AIO to fit onto the rear of the NR200 Case using the pre existing 92mm fan mounts

Dual 120mm fan front panel for NR200, the bottom one helps with GPU temp a lot. The top one is useful if the psu is mounted at the front, and I would recommend cutting a section of the front wall of to expose the entire psu fan. The clip is...

CPU fan shroud for NR200 with Noctua NH-U12. Helps a lot to avoid pulling hot air from the GPU. ... Uses corner screw of the power supply.

This is a simple model, but if you've been wondering if the Phanteks T30 fans will fit in the top of your NR200- they will! And these fan pins are the perfect length to hold them in place! There are two version. The shorter one is perfect for the...

Fan duct to suit a Cooler Master NR200 case. Assists with expelling hot air from the GPU via the top front 120mm fan. Useful for GPUs that exhaust air through the backplate eg Nvidia RTX 3000 series, AMD RX 6000 series. Uses the HDD mounts on the...

adding an M-ATX to NR200 computer case 2 x top 1 x bottom left 1 x bottom center I found that printing it sideways yielded better results

Intake fan duct for air coolers for NR200, prevents CPU air cooler from ingesting warm case air (from GPU or other components) Fits 120mm fans, can likely be scaled up to fit 140mm fans

Fans of different configurations. ...Exploring parametric design features in Fusion 360</p> Category: DIY

Spinning fan blades are sharp - watch your fingers ;-)My top fans pull the hot air out from the case, so I'd recommend printing this using PETG or similar material that won't soften as much under higher temperature. ...I printed prototype of the NoScrew...

Spinning fan blades are sharp - watch your fingers ;-)My top fans pull the hot air out from the case, so I'd recommend printing this using PETG or similar material that won't soften as much under higher temperature. ...<i>I printed prototype of the...