novice iv 3d models
6135 3d models found related to novice iv.thingiverse
I created this 3D model for the Eachine Novice-IV so that I could mount and test whether the quad could feasibly carry a full-size GoPro. I created a mount that allows you to use the top standoff screws to attach it to the quad and another that...
thingiverse
replaces the front cover of the camera on Eachine Novice IV
cults3d
I did not find any STL for mounting my camera on my Eachine Novice IV drone so I designed one. ...It is meant to be printed with TPU Printing: Print on the side with support
thingiverse
Rough draft for Eachine Novice IV drone to attach SMA pigtail. ... Base has been taken from this model: https://www.thingiverse.com/thing:5342436 NOT TESTED ON REAL DRONE
thingiverse
I did not find any STL for mounting my camera on my Eachine Novice IV drone so I designed one. It is meant to be printed with TPU Printing: Print on the side with support V2 moves back the camera a bit , the drone is much more well balanced....
thingiverse
#Beeper Support for Eachine Novice IV 4. - ##Version 1.9 A more low profile beeper support to avoid exposing it to landing impacts. - ##Version 2.0 A wider version allows the button to be placed to the side. ...It's more reacheable if you have a...
thingiverse
#GPS holder for Eachine Novice IV 4. Pictures are for the version 2.2. - ##Version 1.6 GPS holder that it's not dangling from the copter. This support slides in the two final metal pipes and the GPS chip slides into it. - ##Version 2.2 ...
thingiverse
#Antenna tail for Eachine Novice IV 4. - ##Version 3.8 The purpose is to change the antenna cluster to be more discrete and add a slot to add the XT30 plug, avoiding dangling cables. - ## Version 4.3 Lowered the antenna angle and removed Tx...
thingiverse
I remixed bruhmomentum783's landing gears so that even the GPS Sensor wouldn't hit the ground, works great!
thingiverse
### GoPro Camera Mount ## Motivation Usually i use a different support https://www.thingiverse.com/thing:5274370. However I have the Gopro 7 black, and a metal case for it. This makes the camera to heavy and affects the flight caracteristics so...
thingiverse
fpv camera mount for novice 4 ixed to 20 degrees
thingiverse
fpv camera mount for novice 4 fixed to 25 degrees
thingiverse
Bracket for the VTX antenna (4.2mm), the GPS module and two antennas of the receiver.
thingiverse
### Action Camera Mount - ## Action Camera Mount V6 Compatible with most action camera supports. - ## Action Camera Mount V7 Increased the space between fins to accomodate GoPro metal supports. - ## Action Camera Mount V7.3 Added an hexed...
thingiverse
This is a GoPro Hero 9 Sleeve designed to fit on an Eachine Novice IV. There is no telling how terrible this will be for flight dynamics but hey, don't know if ya don't try right? Designed with my software MountMaker. ...www.mountmaker.net
thingiverse
Very simple motor wire protector for the Novice 4. Use a 3.5mm ziptie to secure it to the arm. ...Print in TPU
thingiverse
Simple landing gear for the Eachine Novice 4. Not printed it yet, it should be printed in TPU and fixed to the frame with a 3.5mm ziptie. ...Would provide even more protection from landings when used with the arm/motor protector on my page and can be...
thingiverse
The following settings were utilized during the customization process: difficulty level set to "Novice," build plate selection disabled (build_plate_selector = 0), font type specified as "write/Letters.dxf," and manual build plate positioning with...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=749887\n\n \n \n Instructions\nUsing the following settings:\nwall = 1\nfontname = Source Serif Pro\ndo_shift_font = automatic\nbaseheight_percent = .33\nsize of text = 25\nshift_font_percent =...
thingiverse
Mount pour installer l'insta 360go sur le Novice 2 en position horizontale . ... pour amélioré la fixation j'ai ajouté du double face à l'arrière du print
cults3d
Carmen The Novice Warrior 4 poses 3 Scale for each pose ( 164Scale, 35mm,54mm) Presupported and unsupported model including separate Base the model are test print on Anycubic Photon S
cults3d
This was inspired by one of my favorite MMORPGs of all time, Ragnarok Online. ...In the game you start as a novice, and advance from there to the class of your choosing, like most other MMO's.
thingiverse
This specific sign was designed to meet Russian standards and is required on all vehicles driven by novice drivers with less than two years of experience. The sign measures 150mm x 150mm square, with the exclamation mark standing at a height of...
cults3d
I decided to make this first mod for the Eachine novice II drone, which is a protection system for the arms of the drone, which will keep them safe in case of accidental fall. ...After several tests I created these armguards, guaranteeing constant...
cults3d
patreon.com/dakkadakkastore myminifactory.com/users/DakkaDakkaStore?show=tribe The War Sisters Novice Squad models consists of 32 parts, including 6 heads, 6 bodies, 3 backpacks and 17 weapon options. 2 versions of files are included: pre-supported...
cults3d
I really, really dislike the star nun novices and how they are represented with official releases, so I decided to make my own proxies for a full squad, because dammit, these laser nun rookies are supposed to be training for war, not for a video on...
thingiverse
I really, really dislike the star nun novices and how they are represented with official releases, so I decided to make my own proxies for a full squad, because dammit, these laser nun rookies are supposed to be training for war, not for a video on...