nodemcu esp32 3d models

Case for Nodemcu ESP32 38 PIN

This is a case for NodeMCU-ESP32 (narrow version).

Had to bump up the size for the Dohea nodemcu board because it is slightly bigger

Found case from bkgoodman but my esp32 38 pin dev board did not fit. Remixed to fit an ESP32 38 pin Board. Buttons still work. Led is in a different spot. ...not yet alligned to design.

Case for Nodemcu ESP32 38 PIN

If you connect your Altherma heat pump by following the instructions of the ESPAltherma repository (https://github.com/raomin/ESPAltherma), you can 3D print this design to mount the NodeMCU on the outside of the heat pump (see pictures).Longer cables...

See:  https://www.nabucasa.com/The 3d printed case is a remix which I modified to accommodate  an esp32, an led and an   i2s preamplifier:Parts required:Stereo  media playerEsp32:  https://a.aliexpress.com/_mNcQTWM RGB LED:...

The original design had the case and the lid as a single .stl. ...This is the same design, but the components are split into separate files.

You can print it without supports. I opened the bottom so you can reach the pins from below. ...

... support any cables. I've been using this for WLED and it forms a perfect enclosure for that with power entering at the bottom and then output to LED strings at the top. Note: To use on one of the slightly larger ESP32 boards, just print at 125%

More resources for electronic engineers:https://nmtelectronics.com/product/ai-thinker-nodemcu-32s/

My design for a NODEMCU ESP8266 case with 0.91" 128x32 oled. Based on this model: https://www.thingiverse.com/thing:2786523. ... but redesigned from scratch.

A compact project enclosure designed to hold a 400-pin breadboard and accommodate an ESP32-based NodeMCU board.

For NodeMCU ESP32s, mine says v1.1 on the back. I'm sure it works for other models as well. 3 files, one top, one bottom and one bottom with magnet holes. Most importantly, there is a hall effect sensor under the metal plate that I want to take full...

For my NodeMCU ESP32, the label on the back reads v1.1, which should work with other models as well. The case comes in three files: one top piece and two bottom pieces, one of which has magnet holes. The most important feature to me is the hall...

A remix scaled up a bit to fit an ESP32 nodemcu Category: Electronics

A Human is taking their remix to new heights by scaling it up just right to perfectly fit the tiny but powerful ESP32 NodeMCU.

ESP32 NodeMcu - Case (Lolin V3 no rounded corners) Designed this case because I did not like most of the designs out there. This one fixed all the issues and I'm happy with that hope other people enjoy as well. The lid holds into a grove and the...

This is an ESP32 DevKit V1 enclosure, a compact box with a snap-on lid that exposes the USB port and LEDs while keeping little buttons on the lid accessible even when closed. The board's pins protrude through slits at the bottom of the case,...

This is an ESP32 DevKit V1 case that's a bit of a different design than the previous. This one is a small box with a snap-on lid which exposes the USB port and LEDs, and leaves little buttons on the lid so you can depress the on-board buttons with...

The NodeMCU 32s Developer Board Enlosure.

Measuring the power output of my old ferrarismeter using an ESP32, TRCT5000 pulse counter, ESPHome, and HomeAssistant. Additional sensors are a DHT-22 for humidity en temperature and a cheap PIR sensor for motion detection. The sum of all...

A simple Case for the ESP32 NodeMCU Module WLAN WiFi

Simplistic case for esp32 (devkit c).It has a snug fit for the esp, pin and usb breakout and lets you easy remove the esp board.The case itself is meant to be glued together.The purpose was mainly for my private projects, but I wanted to share the...

... 0.6mm silver plated copper wire (please no comments on my soldering skills!! ;-)With some of my NodeMCU boards the battery holder fits tightly and is hold by the GPIO sockets whereas with others double sided tape is needed to mount it.  

This design is a stacked enclosure for the ESP32 D1 Mini (NodeMCU) module and any attached shields, as offered by various suppliers. It consists of A bottom part (called bottom) with cutouts for USB, reset button and LEDs. a lid (top) none, one or...

My first homemade 3D printed thing. ...Made with Shapr3D on iPad Pro Nothing to say except that I made it cause I didn't find any case for that particular model of ESP32. ... https://fr.aliexpress.com/item/4000366505771.html

SMD component may or may not be as per scale.Micro USB-B created by :- "M.B.I." (Micro USB-B Female 5Pin SMD)---Though I Tried to achieve exact dimensions, please inform me for any inaccuracy.edit 1 :- Added new step file with less details.edit 2 :-...

This basic model of NODEMCU-32 v1.3 board with ESP32 WROVER B Module

Hi, I needed a little box for my ESP8266 with a mount for a rocker switch that I could fit outside my enclosure. Since I couldn't find anything similar I designed my own. The box has some room for the cable management. The inside measures...