nodemcu case 3d models

The mmu file can be used also to remove this difuser. Needed parts: x1 NodeMCU Lua Lolin V3 4xMAX7219 module M3 30mm x4 (close the box) M3 10mm x4 (NodeMCU) Print instructionsLayers 0.2 white PLA recomended. MMU version: 1x this pack:...

This is a case for the DOIT.am brand motor driver shield for the NodeMCU dev board, where 3m double-sided tape will be used to secure the board to the bottom. A single wall thickness on the terminal strip side is meant to be cut out but should...

This case contains an Amica nodemcu v2, a 0.96" OLED display, and a BME280 sensor. The BME280 is inserted into a pocket that can be easily sealed with elastic gum to minimize its impact from the controller's warmth. The rest of the components are...

This case houses a nodemcu v2 'Amica', a 0.96" OLED display and a BME280 sensor. The latter gets slipped into a pocket which is easy to seal off with a little elastic gum so the measurements are a bit less influenced by the controler's warmth. Adding...

This case houses a nodemcu v2 'Amica', a 0.96" OLED display and a BME280 sensor. The latter gets slipped into a pocket which is easy to seal off with a little elastic gum so the measurements are a bit less influenced by the controler's warmth. Adding...

This case houses a nodemcu v2 'Amica', a 0.96" OLED display and a BME280 sensor. The latter gets slipped into a pocket which is easy to seal off with a little elastic gum so the measurements are a bit less influenced by the controler's warmth. Adding...

It's worth noting that this design is predicated on the NodeMCU v0.9 due to its relevance at the time of creation, which was specifically commissioned by a friend who possessed an assortment of these older units. For optimal results, this enclosure...

I designed this tally light case.The usb cable can be fixed in place with a zip tie.Insert some metric nuts during the print.1x M4 Nut on the bottom4x M3 Nut for the lidScrews:M4x20mmM3x16mmI used this setup:...

I modified the design with two versions of a cut out at the back of the arm, accommodating 2.2 display screens that already have pin outs soldered in place to fit seamlessly into the case. The files labeled lower and upper are specifically designed...

I'm updating my weather station setup by swapping out the original LCD display for a new one that fits perfectly onto an ILI9341 screen and also giving it a custom home with a sturdy Nodemcu mount.

On the next two photos, you'll see the integration of an Arduino Nano with my Ambilight laptop setup and on the last two, a Lolin NodeMCU paired with my AmbiPiBox case designed for Odroid's and Raspberry's. This case also serves as a single...

Improved version of ESP8266 NodeMcu v2 (1.0) DHT22 Case with enhanced temperature accuracy. The upgraded design features a significantly reduced error margin, now just about 1 degree Celsius at 20 degrees Celsius compared to the original's 7-degree...

This is a versatile wall mount enclosure specifically designed for an ESP8266 NodeMCU, complete with a built-in 1x DHT22 temperature/humidity sensor module. The case consists of two distinct parts: a lower base that features four screw options for...

This is a compact setup featuring a single NodeMCU board paired with a TFT screen of the ILI9341 type. Three distinct components are required for assembly. ...The weather station's programming is courtesy of the team at GitHub, specifically squix78.

Used hardware: Amazon (fast shipping, slightly higher price) * NodeMCU v2: https://amzn.to/2RHRkBv * AM2301 / DHT22: https://amzn.to/2H0oDv9 * Relay: https://amzn.to/2Rbm3ak * Jumper Wire: https://amzn.to/2SG344D Gearbest (longer shipping, cheaper)...

I've built this project specifically for the Lolin Wemos D1 Mini ESP32, leaving some room for a sensor to be easily added.

Our AmicaV2 Module stands out as a vital component, designed to be fully assembled and ready for use. Its versatility makes it an attractive choice for any project that demands a high level of customization and adaptability. ...By incorporating the...

Designed this case for my NodeMCU 1.0 ESP-12F ESP8266 board. Ordered a bunch of those from AliExpress (e.g. https://www.aliexpress.com/item/1005001621705950.html) and needed a case to fit them. Case provides access at the front side to micro USB...

This is a case for a ST7735 TFT display including the cable connector, and an Arduino Nano or SBC-NodeMCU board. The display as well as the MCU board can be put in place without screws or glue. There's space for several components: * A DHT22...

Designed this case for my NodeMCU 1.0 ESP-12F ESP8266 board. Ordered a bunch of those from AliExpress (e.g. https://www.aliexpress.com/item/1005001621705950.html) and needed a case to fit them. Case provides access at the front side to micro USB...

Customized version of https://www.thingiverse.com/thing:3391397 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3391397

I designed a compact case for a DHT22 humidity and temperature sensor paired with an ESP8266 microcontroller. Credits -------- This is an adapted version of Onshape user Hunter Horsman's original design. Improvements/Changes ---------------------...

The ideea is based on two Tinkercad designs:The cutout in the top of the case (I used this for the cutout) : https://www.tinkercad.com/things/gMEKJZMkh9p-wifiThe design itself (re-created from scratch):...

<p>This is my remix of the <a href="https://www.thingiverse.com/thing:2363763">Sensor Node Enclosure for ESP8266</a> by <a href="https://www.thingiverse.com/calvinboey/designs">calvinboey</a> on <a...

Here's an additional design that was requested but I couldn't locate earlier, so take a look and have fun!

Modified casing designed specifically for the HELTEC version of NodeMCU, featuring an integrated 0.91-inch OLED display and a dedicated opening for lithium battery adapters. A simple printout using PLA material is all that's required to bring this...

Case for the NodeMCU ESP8266, a versatile 4-Channel Relay Board, and the DHT11 temperature sensor, all neatly paired with an OLED display measuring 0.91 inches in diameter. Perfectly suited for intelligent home automation systems. ... Crafted by Ruben...

The LCD Display and NodeMCU are securely fastened to the case using M3 (3 mm) screws, which are spaced out by four spacers for each component. The LCD Display is positioned at the bottom of the enclosure, while the NodeMCU ESP8266 Board is mounted...

## Introduction A simple case to house a NodeMCU v3, a double 5v relay, a BME280 temperature and humidity sensor and a small switch. I use this case to make my boiler smart by replacing the connection to my thermostat with one of the relays, though...

My version fits the alternative version with different dimensions as shown on the attached photos:  I've also...