node 202 fan duct 3d models

I'm replacing the feet on my Node 202 PC cabinet with Fractal Design's new design. They're a lot smaller than the originals, which is nice because it gives me more space to work with. The squared holes at the bottom of each foot are perfect for...

Replacement stand for Node 202 exceeds expectations by not blocking any exhaust ports for the GPU. Combined with expert undervolting techniques, my GTX 1080 consistently runs at 70c @1987mhz. I designed and printed this replacement in PLA and have...

Small stand for fractal design node 202 is a clever solution to improve airflow around the GPU. By covering the original mount, you're allowing air to flow freely through this crucial component. To set up your small stands, start by printing two...

I engineered this component specifically to support the bottom of my dual PCIE bracket GPU, eliminating any sagging when mounted atop my Node 202's 120mm x 25mm intake fans. The standard case bracket normally occupies one of the mounting points, but...

Modified design, more drives for Fractal Node 202. ...Thinner drive caddies and no holes in the mount base.

Fan shroud for the Fractal Design Node 202 case with the Asrock X470 Fatal1ty mainboard and NH-L9 cooler. The problem is that (depending on case orientation) the fan is not sucking fresh air from the ventilation opening, but instead using the already...

Custom CPU exhaust fan bracket engineered for Fractal Design Node 202 compatibility, securely holding two Noctua 40mm x 10mm fans in place. Installation involved cleverly positioning this bracket between the motherboard and side vents using 3M...

I wanted to mount a 3rd 2.5in drive in my node 202. Mounts in the GPU / radiator area with M3 screws and washers. Compatible with short GPUs or single fan radiators Recommended for use with SSDs over HDDs Required Parts: 2 - M3x12 Screws 4 - M3x6...

An older project that I wanted to upload.I wanted to mount a 3rd 2.5in drive in my node 202.Mounts in the GPU / radiator area with M3 screws and washers.Compatible with short GPUs or single fan radiatorsRecommended for use with SSDs over HDDsRequired...

An older project that I wanted to upload.I wanted to mount a 3rd 2.5in drive in my node 202.Mounts in the GPU / radiator area with M3 screws and washers.Compatible with short GPUs or single fan radiatorsRecommended for use with SSDs over HDDsRequired...

The IS60 Evo just barely fits a node 202. But you need to remove the filter and the metal plate with its slots can create quite a bit of noise. So remove the metal plate and close the gap with this. This is a rough draft that fits, YMMV...

My Fractal Node 202 case sits in a media shelf, so wanted to raise the case to get some better airflow. Designed in Fusion 360 and designed to take a couple of 8x2.8mm rare earth magnets. ... Printed in PETG 0.4 Nozzle 0.2 layers

Legs for the wonderful Fractal Design Node 202 case. The original stand prevents air flow from the bottom. These pop on easily, but have a firm fit and can be shifted into the right position. Airflow is improved. ... You can use the FreeCAD source file...

The better airflow can reduce your CPU temperatures by 10-15°C.Right now it is printed in ASA and CPU reaches 48°C normal browser use. If your case reaches high temps i suggest printing in PETG, ASA or ABS.More details follow after benchmarking,...

To access the two remaining models, you'll need to flip both of them over. ...For the node 202, make sure it has standoffs installed to securely attach an MB16AC power adapter with its protective casing.

A shroud to replace the stock one found on the wraith stealth cooler Made to fit the node 202 WITHOUT the CPU dustfilter. STP included so you can "squish it to have the dustfilter or the spire. ... PETG or ABS are preferred but PLA seems to be fine

Node 202 Stand/Feet - Print x2 Provides a gap of 10mm between the bottom of the PC and the desk. Plenty of stability, and a good fit thats not too snug. Overlaps the GPU dust filter to keep it in place. ...

Shorter feet for Fractal Node 202, remixed from https://www.thingiverse.com/thing:3013820 Gaming Computer Riser / Tall Foot by flyattack Attach to the computer case with thin double-sided mounting tape. Notes: PLA works great for this print.

This stand offers a superior alternative to the standard Node 202 computer case stand. The original stand significantly obstructs side vents, severely impairing airflow and contributing to elevated internal temperatures that are already difficult to...

This is a front and rear stand for the Fractal Design Node 202 with USB/SD/Micro SD storage on the front. It provides approximately 30mm of lift to increase exhaust when in the vertical position. This does not block the original intake and barely...

It's fantastic that they incorporated a support/brace for the graphics card into the Node 202 case, but unfortunately, it doesn't work seamlessly with every card. My Asus Strix 1070 happens to be a bit too wide, and their support piece can't slide...

... it with two M3 1cm long screws and nuts in place. If you want to add a fan, you'll have to modify the entire front of the case and create a path for the fan cable - good luck, you're on your own. ... Four months later, and it still works well.

This creation was crafted with precision using Tinkercad's powerful tools. ...Make your own edits and improvements directly online at https://www.tinkercad.com/things/q5KU3Tq7a2y

Custom-Made Computer Case Ducting for Fractal Design Node 202 and EVGA ACX3 Designed specifically for the Fractal Design Node 202 case, this custom ducting system is engineered to work seamlessly with the EVGA ACX3 graphics card. Additionally, it...

I mounted the original remix in a Fractal Design Node 202, transforming it into a NAS server build. To secure the rack in the GPU area of the cabinet, you'll need M5 nuts and bolts. Attach the nuts to the rack with superglue, then screw the bolts up...

Needed to raise my Fractal Node 202 up a bit for better airflow in the horizontal position. There are some designs here that do just that, but utilize double sided tape to attach to the case. I wanted to instead hold the feet on using the case...

I'm creating a new design for a custom hard drive enclosure with added rigidity, inspired by the original model from Thingiverse (3316732). ...The goal is to provide extra support and stability to the hard drive while maintaining its accessibility.

I found a file a long time ago and I cant find the original anymore, anyway I'm not using the standard amd cooler any longer, so modified this as best I could in fusion 360. It was a stl so didnt import exaclty in 360. Works well if you use this case...

cooling fan duct

MY FAN DUCT