noctua nf a4x10 3d models
4476 3d models found related to noctua nf a4x10.thingiverse
Fan cover with a small recess for installing a filter. ...Designed for Noctua NF-A4x10 FLX, using the hardware included with the fan. ... Originally modeled in SOLIDWORKS, .stp available upon request
grabcad
... attached model is just the shroud, not the actual fan. For those interested in building around it like me, you can visit Noctua's website at http://www.noctua.at/main.php?show=productview&products_id=47&lng=en&set=1 for more information.
prusaprinters
With a Noctua 40mm fan in hand, I decided to play around with air flow.This design pumps air from the back in the case past all the major components on the board.A little bit is diverted past the bottom to cool the M.2 slot.I set the fan to turn on...
thingiverse
Simple fan mount for Raspberry Pi Compute Module 4 (CM4). ...Fan is a noctua NF-A4x10 40mmx10mm. Requires no additional hardware, just snaps in. ...Has clearance for a low profile heatsink.
thingiverse
I was fed up with the noise from my Radial/Centrifugal blower on my CR10S Pro motherboard. ...So I crafted a bracket to house an old NOCTUA NF A4X10 FLX fan that blows directly onto my CR10S Pro motherboard.
thingiverse
This is a simple plate mount designed to hold a Noctua NF-A4x10 fan over a Raspberry Pi. It's intended to be mounted above the Pi using M2.5 standoffs via the Pi's standard mounting holes. The fan mounts with M4 bolts, which easily thread into the...
grabcad
PI-EXP project: Conceived by Noctua's design team, the NF-A4x10 5V boasts a cutting-edge aerodynamic design that incorporates Flow Acceleration Channels and an AAO standard frame. This 40x10mm fan is specifically engineered for high-performance,...
prusaprinters
(you can install it with the rubber Noctua mounts or the screws) and plug the noctua fan in to 12 VOLTS! red connector. ...Make sure to plug it in correct polarity (red on +, black on -).Model orientation:Print settings:Perimeters: 3Infill 10%...
thingiverse
This setup is tailored specifically for a pair of 40mm Noctua fans. As a result, the printer operates in near silence, with airflow evenly distributed across all components. ... To complete this configuration, you will still need to acquire four M3x20...
thingiverse
Using a Noctua Fan - check photos for how I mounted it. used the rubber parts in the fan packaging and clipped off the excess. Photos show the Pi4 mounted to a screen , but this part works without that too. I ended up cleaning out the holes a...
thingiverse
Anycubic Kossel Single + Dual Fan Adapter for Noctua NF-A4x10 (40mm Fan) This adapter is designed specifically for the 40mm Noctua fan, but it should fit most other 40mm fans without any issues. If you notice anything that doesn't quite fit, please...
thingiverse
It's Not the Smallest or Most Elegant Design, But It's Easy to Print and Allows for Efficient Cooling with a 40x10 Fan (I'm Using Noctua NF-A4x10), Lowering Temperatures from 60+ C to Approximately 35C in My Setup - See Screenshot for Proof. A...
prusaprinters
So I have made one. It is not the smallest one or the fanciest case, but it is easy to print and there is possible to mount 40x10 fan (I am using Noctua NF-A4x10) so temperature can be significantly lowered (from 60+ C to cca 35C in my case - see...
cults3d
It is not smallest one or fancy designed case, but it is easy to print, it is possible to mount 40x10 fan (I am using Noctua NF-A4x10) so temperature can be significantly lowered (from 60+ C to cca 35C in my case - see sshot). Intentionaly big hole...
prusaprinters
Additional parts needed:Rasberry Pi 4b40 mm PWM 4V Fan (such as Noctua NF-A4x10 5V PWM)4x M4 countersunk screw (Normally supplied with the fan)Optional: 4x M3 nut and 4x M3x6 screw (To screw Raspberry pi securely into the case)Print settings:Works...
thingiverse
Remix of https://www.thingiverse.com/thing:4907413. The spacers and all the mounting pieces were molded in PETG (amazon PETG). I created the holes for the screws and the main hole to insert a new cooling fan, with the dimensions of 40x10mm...
grabcad
Noctua's NF-A4x10 fan features precise outer dimensions but approximate inner blade measurements due to difficulties in obtaining exact figures.
thingiverse
I discovered a great design for a velocity stack for 40mm fans that I was going to print out, but found it had a larger center hub cover than the relatively small 17mm motor hub on the Noctua fan. Several people asked for a Noctua fan version, but...
cults3d
I left a comment on the original thing saying I had a modified version for the Noctua fan available, but there was no interest from the original designer. Recently, someone contacted me who was interested in my modified STL file, so I sent it to...
prusaprinters
I commented on the original thing that I had a modified version for the Noctua and I could supply it, but no interest from the original designer. I was recently contacted by someone who was interested in my modified STL, so I sent it to them, but...
thingiverse
- added a Noctua Fan on the side This remix is more effective and more quiet! ... Print Settings: Low Quality: 0.28mm Infill Density: 20% Infill Pattern: Lightning Printing Temperature: 220°C Build Plate Temperature: 60°C Print Speed: 60 mm/s...
thingiverse
... the case. ... It becomes part of the outer case. Parts needed: -Asrock Deskmini x300 or a300 -Noctua L9a -Noctua NFa4x10 x2 -McMaster Carr 94510A240 m3 Brass inserts x7 -m3-8mm x5 -m3-25mm x2 -Bit of glue or sealant to make the 40mms permanent
thingiverse
Liked the lid! ...Made a remix to fit my fan. (Noctua NF-A4x10 5V)
thingiverse
Replace the original lower cover on the Creality Ender 3 Pro to install a high-quality Noctua NF-A4x10 fan.
thingiverse
This is a cover for Noctual Fan 40/40 mm Can be used on Noctua NF-A4x10 or Noctua NF-A4x20 FLX - 1mm thickness
prusaprinters
Box for Raspbberry Pi 4B. ...You can use screws M2 8 mm. Fan is Noctua NF-A4x10 5V. ...Print instructionsMaterial ASA.
cults3d
NOCTUA fan support for motherboard; valid for Noctua models NF-A4x10 and nF-A4x20