noctua desk fan 3d models

The fan is situated centrally above the mainboard - I used a Noctua NF-A9x14PWM with the Low Noise Adapt NA-RC7. I recommend using the holder version with three feet. Important: To allow better airflow, I turned off the groundplate (previously, air...

I choosed a Noctua NF-A4x20 FLX wich is bigger than the stock one but it is also 12V so I still needed a buck converter.Since my motherboard has a 12V 8025 Noctua connected to a buck converter in the hotend power pins (always on) I decided to connect...

I've changed most of fans in my Ender3 s1 to noctua. Since they need a stepdown I've designed this case mounted on a 3printer. Rails are a bit of a thight fit, but at least they don't move when you carry your printer. ... To mount the board to the...

This is a custom adapter designed specifically for Noctua fans measuring 40mm x 20mm, allowing them to fit seamlessly into the standard shroud found on the BLV Mbn cube. ...Its performance matches that of the 50mm blower, yet it operates with...

Want an easy way to prevent that whit out requiring any tools or hardware?Introducing the AMAZING CILP ON FAN COVERS!!!!!!!Just print them clip them and BADABING BADABOOM you're done no more getting those fingers caught on blades or having to remove...

... with double-sided tape for secure attachment. The fan itself is secured using screws, Noctua rubber pins, or zip ties, providing a safe position regardless of the chosen fixture – as clearly demonstrated in the attached image from my Predator.

This fan guard is perfect fit in size for Noctua 40mm fan. Required screws:3x M3x14 screws1x M3x25 screwPrint settings: Filament: PETGLayer height: 0.2mmSupports: noPerimeters: 2Be careful not to over-tighten the screws, otherwise the...

This is a Noctua NF-A4x10-5V fan mount for Sega Naomie 2 as a replacement for the original Sepa HFB44B05A. More information on [Arcade-Projects](https://www.arcade-projects.com/threads/replacement-naomi-fans.2949/) or my post on...

I extended the front heat sink fan to fit a Noctua NF-A4x20 fan. I also included a second version that has a BLtouch mount off the side. I printed both of these with the "top side" on the build plate - no supports for the non-BLtouch option...

https://noctua.at/en/products/fan/nf-a4x20-5v-pwm This fan size allows it to fit nicely without getting in the way of too many wires, while pushing more air and being more quiet than the stock fan. This bracket positions the fan right in front of...

To assemble this project, you'll need a few key components in addition to the parts already mentioned and a 5V Noctua (or equivalent) 40mm fan. Four M2 25mm bolts and four M2 nuts will secure the fan itself, while four M3 12+mm bolts and four M3...

... be printed with the right color matching what people had chosen. Also hides the BLTouch at the same time. The fan is the Noctua 40x16 but I suppose it could work on other fans. I've included the step file for it. ... The 2 screws are M3x20

I designed this case to fit a Raspberry Pi 4B with heatsinks and a Noctua fan. I also added a barrel jack so that all the cables come out the back. I have included a version without the hole for the barrel jack if you'd prefer to go with that. ...The...

......To start, I'm swapping out the 50mm fan with a more compact 40mm Noctua fan, which fits perfectly into the existing design. Additionally, I've added a handy pass-through for the fan wires since I'll be mounting this panel on the outside of the case.

This perfectly sized design fits snugly around a Noctua 40mm x 10mm fan. The fan slips seamlessly into the top square, ventilating the Pi from above. The case lid is generously high enough to accommodate a genuine Pi PoE Hat and a Pi-EzConnect...

PS2 Noctua Fan housing (NF-A6x25) Information I couldn't find any available, so decided to make my own. Idea had been to be as non-destructible as possible, so this one clips into the fan-grill on the back. Due to printed clips not being the most...

This will be soldered to the new DC-DC buck converter. Using the same wire cutters, trim the cable on the Noctua NF-A4x20 fan, preserving at least 2-3 inches of length still attached to the fan (DO NOT REMOVE THE FULL LENGTH). Separate the three...

Fan mount for facilitating Noctua 40mm hotend and filament cooler using two fans. Print Settings Printer: Elegoo Neptune 2S Rafts: No Supports: No Filament: Inland PLA Notes: I don't recommend using Noctua 40mm for a blower but if you want to this...

Hence I made a cover for the Noctua fan as found here: https://www.thingiverse.com/thing:2730049 When Prusa released the new MK3S parts, some modifications to the cover had to be made, to fit the new Prusa parts. The principle remained the same: The...

I created this control box case because I wanted to reduce the noise of the control box fan by replacing all original fans with Noctua fans. The original 60mm fan is only 15mm thick, but the Noctua fan (A6X25 PWM) is 25mm thick, making it impossible...

This is a replacement fan housing with fan guard for the 3 center fans of my Supermicro CSE-836 case as I didn't want to cut up the original ones to fit my Noctua NF-A8 PWM fans. It should be compatible with loads of other Supermicro 2U/3U/4U cases...

It is meant for the OEM Hotend with the Noctua Fan Mod. I Printed in .16 but I don´t think it matters too much. Print with Tree support but look for NO SUPPORT INSIDE of the part cooling channels. ...You may never remove them from the part after...

Just upgraded my Creality Ender 3 by replacing the stock psu fan with a [Noctua fan](https://www.amazon.com/gp/product/B00VXTANZ4) (60×25mm). Sadly, this super fan is too thick to fit inside the psu unit. So I mounted it outside (just pass the cable...

They should snap into the fan holes, the flexibility in the model will ensure that they stay clamped.They might work with other Noctua coolers too but you'll have to adjust the size, either by scaling in the slicer or better yet open the attached...

You can use this to elevate a Noctua NF-F12 fan off of a surface and then also use another as a platform on the other side of the fan. It comes apart really easily, so you could use something like hot glue or melt the posts a bit to make them bulge...

They should snap into the fan holes, the flexibility in the model will ensure that they stay clamped.They might work with other Noctua coolers too but you'll have to adjust the size, either by scaling in the slicer or better yet open the attached...

It securely holds a high-performance "Noctua NF-A4x10 FLX 40mm" fan, renowned for its silence, as well as a compact "DC DC Buck Converter Step-Down Module" measuring 22mm x 17mm x 2.2mm in size. ... A small potentiometer is cleverly integrated onto the...

I use it with 2 40x20 Noctua Fans with an Y connector connected to a stepdown module (which was already attached to the fan power supply from a former mod) I Just uploaded this so other people can just get these files in one place, not to claim...

I designed a fan-mount to install my Noctua NF-A4x10 40mm fan on a Pi 4. You can use the original screws which came with the fan. The mount is screwed down with 3x35mm wood screws. Between the fan and the heatsink is a clearance of around 2mm. You...

... ... A self-printable riser/fan mount for Monoprice Mini Delta is now available, allowing you to attach a Noctua 120mm fan (NFA12x15 FLX) from Amazon. This fan delivers extremely quiet (almost silent) stand-by noise and exceptional cooling performance.