noctua 4010 fan 3d models

This is a modified dual outlet fan duct that I adapted from sirhcwolf's original design to work seamlessly with my fan shroud for the JGMAKER MAGIC. My fan shroud can be found at https://www.thingiverse.com/thing:4426539. You can also find...

Featured in Fan_Showdown S03E03: https://www.youtube.com/watch?v=I2lxGYplpMA Also featured in comparison of profesional fans here: https://www.youtube.com/watch?v=FrVtVHSW3_w Cheater is built around three basic ideas: 1. Exploit the rules of the...

This is a 3D printable bracket for hanging two 40 by 40 by 10 mm cooling fans. This part requires fairly good bridging, but no support material. ...Printed with ABS.

I really liked the RPI 4 case done by "ArtieH" but wanted it to use a more standard 4010mm fan, and while I was at it-- i replaced the OctoPrint logo with the mainsail logo.

I originally posted these on my Minimalist Dual Cooling Fan for Aquila / Ender 3 V2 https://www.thingiverse.com/thing:5263939 This design is a much better fit. ... this is a remix of: https://www.thingiverse.com/thing:3365114

I originally posted these on my **Minimalist Dual Cooling Fan for Aquila / Ender 3 V2** https://www.thingiverse.com/thing:5263939 This design is a much better fit. ... **this is a remix of:** https://www.thingiverse.com/thing:3365114

Muffler designed for the heat brake cooling fan for the Petsfang Bullseye fan duct for Ender 3. Tested with Bullseye on Ender 3 Pro, should fit all Ender 3 printers with Bullseye modification. Print laying flat on its face as shown in the picture...

So yeah wanted a fan for me SB2040 board but did not want to buy a 3010 or the 7mil version when I already had extra 4010s around.  Printed with supports (this was a quick build did not invest time into making it print without supports).  Watch for...

Installation: For a seamless experience, we recommend taking off the fan shroud from your other fan before installing the grill. However, if you're in a hurry, you can still get the job done without removing it. ... The fan clip is designed for easy...

I used a mount that The 300lb Gorilla designed for me to mount the fan along with the EZABL micro. To mount the fan on the left side, I drilled 1.5mm holes for the top holes and used M2 bolts. The duct mounted with 2 bolts with nuts on the...

I increased the height of the sides that snap-on. ...The 20mm depth fans have a thicker lip so I had to modify the original. ...All credit goes to bkvines, the original creator.

All credit goes to the original designer, bkvines. ...I found that with my installation I did not need the fan screw holes in the cover so I simply filled them in. That's it. ...Nothing else is different.

This is a Remix from Major Hardware Deskfan, but with Laminar Flow. ...With this you will get a gentle Airstream, like a Dyson Fan. Happy Printing. ...Best to print it with 100 infill

i really liked this design but the fan i got seems too thick for this design so increased the height of the fans. also the top part where you screw it in kept snapping off so i reinforced it. also the side vents kept snapping so i made them...

... work on any thicker 12/24v psu with the same lid screw holes. ... There are two models, one for a 15mm thick fan which would fit with no modification and one for a 25mm thick fan which has a n additional piece that sticks out of the back of the cover.

... in chinese Machinist or Atermiter X79 board. ...Its just plug and play, just fit it and it will stick fine. Just draw 12V from CPU fan and you will have it fully working. ... Be free to modify it if you need it, I'm just a newbie using Tinkercad ;)

A bracket to attached NF-A9x14 to my 1080 mini; helps reduce the noise profile. ... Print in PETG though ABS is probably better - so far my PETG is holding but I don't game much these days. I used M3 bolts & nuts to secure the fan to the bracket.

A bracket to attached NF-A9x14 to my 1080 mini; helps reduce the noise profile. ... Print in PETG though ABS is probably better - so far my PETG is holding but I don't game much these days. I used M3 bolts & nuts to secure the fan to the bracket.

This is a remix of the 120mm fan duct from moriaty_ (https://www.thingiverse.com/thing:4495123). Credits to him! As Thingiverse obviously suffers from technical problems when publishing a Remix I had to create a new page, which you can find here: ...

________________________________________________________________________________________________________________🇬🇧English🇬🇧 ((In 🇫🇷Français 🇫🇷 at the bottom of the page...

This is my remixed model that makes it far more secure, eliminating all rocking/wobbling, and fits it with the Satsana dual fan remix with the BL touch mount. So, I chopped on it all. Anyone want to improve it and make it prettier? ... ...

Working with extremely limited autocad experience but I really liked this fan cover designed by GTPlus. (No obstructions=quietest possible) What I've done: -Removed a few parameters (side screw holes and screw hole mounts). -The original design...

Other Hemera ducts are for large blower fans, often at an angle, which is fine for bed-slinger printers, but severely reduced my Y-axis on my Ender 5. The bottom surround is definitely someone else's design, but I tried so many so long ago I can't...

I liked the original but it had an issue that bugged me, for the screw to insert into the mount and fan the fan had to sit crooked. I also wanted to add a fan shroud to it. This version has the mounting arms moved and additional ones to screw in the...

in total this modification has the following: - Slightly thicker edges of each fan mount (by just a few millimetres) - Each flat side is cleaned up to make sure there are No leftover elements that could disrupt the end result. ... - sharp edges on the...

This isn´t my own model it´s remixed for better fit on my CR10s PRO V2Fan duct was mounted too low and the exhaust was too long so it was hitting my prints and ruining one of them after it snapper after the drag on printed layers so this is my remix....

This thing is possibly crap, but I'm posting it anyway just in case someone could maybe get a little bit of use out of it so my time spent designing it wouldn't be entirely wasted.I made this for my DIY printer but then switched to the fan being...

This is my remixed model that makes it far more secure, eliminating all rocking/wobbling, and fits it with the Satsana dual fan remix with the BL touch mount. So, I chopped on it all. Anyone want to improve it and make it prettier? I was still...

I created it, because I was eager to experiment with a new cooling fan design and didn't have a 5015 on hand. So, I rapidly designed this adapter. It can be printed out as an independent part, remixed or combined with another STL file while...

I replaced the 4020 cooler with two 4010 fans.