no more spool space 3d models

Couldn't find a side spool mount that sits flat on the table and doesnt require any extra bolts and nuts, so I decided to make this. My apologies if there are already designs like this that exist. How to mount it? 1. Insert your T-nuts into the...

... with other sizes. *Update: Following user feedback regarding structural issues that led to build failures, I have significantly reinforced this design and incorporated increased tolerance, ensuring a more robust and reliable performance.*

This model was designed specifically for the Makerbot Replicator 1 and can be printed using inexpensive filament purchased from 3d-printer.no. However, it may not fit existing spool holders, so measuring is required before printing. ...The author has...

... hardware laying around to screw/attach upgrade parts for the Ender 3. That's why I remixed the direct drive spool backet from GobRob (thanks for his good work). ... No extra screws are needed anymore, it just threads in the top rail just fine.

This design builds upon qpolarbear's boltless side spool mount, incorporating elements that enhance functionality while avoiding potential issues with the z-axis stepper motor and removal difficulties based on orientation. The original spool made...

The changes in this remix are: • Tweaks to the "Floor_platsa_spool_holder" so it can be printed with no supports needed, printed laying down, printed in a shorter time, and printed with needed additional clearance. • Tweaks to the...

I needed a spool bracket that didn't require any more nuts and bolts than the original mount. I was going to print this https://www.thingiverse.com/thing:3303879 but as it is too short I moved to this https://www.thingiverse.com/thing:4712916 but I...

Only a few modifications were made to save space, approximately 6 mm, because I encountered trouble closing the door possibly due to the width of the Spool (70mm). Additionally, the initial diameter of the cone was increased for my 55mm internal...

The changes in this remix are: • Tweaks to the "Floor_platsa_spool_holder" so it can be printed with no supports needed, printed laying down, printed in a shorter time, and printed with needed additional clearance. • Tweaks to the...

Here is my solution to Creality’s spool holder, designed to work with CR-6 SE (it may work with other creality printers, I think the mount is standard across ) Utilizes standard 608 ball bearings, the 3D models are made to fit these https:...

Here is my solution to Creality’s spool holder, designed to work with CR-6 SE (it may work with other Creality printers, I think the mount is standard across)Utilizes standard 608 ball bearings, the 3D models are made to fit thesehttps:...

The spool holder simply slides into the grooves without requiring this removal, offering a convenient and hassle-free solution. ...It's possible that a similar design may already exist, but my primary motivation for creating this model was due to my own...

As a result, no support is needed, and bearings are unnecessary for these innovative spool adapters! However, this modification required extra effort - when I exported the initial designs, I discovered that simply filling in the hole left internal...

 Multiply this by 5 spools and with all the struggles of the MMU2S I wanted to find a different solution, one I think builds on the design but is more reliable.  I therefore take the stopper from the NoClunk design and use a two part/dual material...

Modified spool holder now compatible with screws or screwless installation options available.

... otherwise. **Why This Adapter Excels:** - Designed for seamless filament changes without unscrewing anything - Strong yet doesn't waste filament - Prints quickly - No bearings required This is my first design; please keep your feedback gentle.

Screw these down until they touch the box, but be careful not to strip the plastic out by over-tightening.Screw your filament receiver (it's pre-threaded) onto the end of one of the tube connectors to seal it off, which leaves space inside for about...

Screw these down until they touch the box, but be careful not to strip the plastic out by over-tightening.Screw your filament receiver (it's pre-threaded) onto the end of one of the tube connectors to seal it off, which leaves space inside for about...

... along with my remixed washer. If the shaft doesn't fit well, heat it up and pinch it with some pliers. I'd be really happy if you could post some pictures of your project! Printer Settings: Brand: Up! Printer: Up Plus2 Rafts: No Supports: No

... enables wider spools than the standard design, accommodating diameters up to 76mm. If you require custom-sized spools not shown here, simply send a message specifying your desired outside diameter, and I will upload a new file accordingly.

... using wing nuts. For MatterHacker spools, replace the 4" tap bolts with 6" ones and use two additional nylon spacers per spool. ...Optional assembly instructions without skateboard wheels are also provided for both MakerBot and MatterHacker spools.

... Print in its current orientation. I printed this with no supports or rafts with 8% infill density using the "gyroid" pattern in Cura and standard PLA settings. Took about an hour. Please comment with any questions or feedback. ...Enjoy!

Useful print, redrawn to be more angular and simple to print with no supports. Just slice it oriented so the intriguing sloped element grows outward with height. ... # Thank-you original designer.

This Spool holder is designed to hold up to 1kg spools without requiring any mounting hardware, and its profile neatly hooks into the channel of the Black Widow frame while the weight positioned over the back keeps it securely in place. They are...

The Ultimate Spool Holder Showdown: A Customized Masterpiece for the Discerning 3D Printing Enthusiast's Competition, Boasting a Dazzling Brand Identity.

Remix of a decent angled spool holder. ... Only downside was the lack of support sideways, which resulted in the bracket flexing backwards when a full roll was loaded.

Simple Spool Holder for Wanhao D6 3D Printer. Place the part upright (thread facing up) to print without any support material needed. Works great for larger spools. Update 04/12/2018 The original design prints fine with PETG, but failed near the...

This only costs 3 Dollar an it leads the Filament strait from the Spool Holder to the extruder with no lift or side forces applied to the Extruder. Print best all 3 parts separately after another, so the printer is faster and the surface looks...

Key Spindle Dimensions: The major spindle stands at 50mm tall The smaller spindle measures 30mm in height Enhanced Smaller Spindle Options: I offer a new 30mm spindle variant with thicker walls Instructions to Construct Your Own Custom Holder: To...

As most of my spools have 50mm diameter hole I designed another spool holder which has two benefits: you don't need any other parts, bearings etc. and it has really low friction. Now I am happy with it as will use it for much longer time :) PETG...