nixie tft 3d models

Case for the ESP32 D1 mini and a TFT 3.2 inch (ILI9341). I designed this to connect a ham radio transceiver FT-817 or FT-818 to the display. The USB port of the ESP32 will later only be used for programming, while the cable on the back is connected...

BOM: * SKR 1.3 * TFT 35 V2.0 * Fan 40x40 * 8 x Self-tapping screws 2.5 x 10 mm You can find the MPCNC modification of BTT TFT35 FW at the following link: https://github.com/ercoleg/BIGTREETECH-TouchScreenFirmware New Features: 1. The ability to...

The challenge I faced was finding an ideal case for my Raspberry Pi 2, which demands better performance, especially when paired with OctoPrint, a camera module, and OctoPiPanel on the Adafruit TFT display. Given that I had a Raspberry Pi 1's PiTFT...

Nano PI NEO / NEO2 + 2.8 SPI TFT enclosure High-quality, two-part, 2mm-thick walls are optimized for 3D printing and feature no screws or a push button that is easily accessible. The design resembles an old TV. Two variations of each part exist in...

This housing enables the installation of a touchscreen with octopi/octoprint_tft on Prusa MK3s printers, specifically designed for space-constrained environments where the touchscreen must be mounted on the side of the printer. It sits atop the power...

After damaging the controller in my X3S I bought a MKS Robin V1.0 Controller from Banggood which came with the TFT 3.5 screen and a WIFI Adapter. The screen is so much nicer than the original Xvico one and I loved the fully customisable firmware...

The intent is to power off the printer and simply flip this recessed switch (accessed thru the last vent slot alongside the USB connector) using a pen or small screwdriver, to disable the TFT screen for flashing. I did not want block any airflow...

Here's a list of parts I used for this project: RECEIVER: - Arduino Due R3 - 3.5" TFT display - DS3231 - Real time clock - DHT22 - Temperature/Humidity Sensor - NRF24L01 TRANSMITTER: - Arduino Nano v3 - DHT 22 - Temperature/Humidity sensor - BMP 280...

I was searching for a good looking case for my Raspberry Pi 4 and my 7 inch TFT touch screen. I wanted to modify my Creality Ender 5 to use this touchscreen together with Octoprint and without the standard LCD display and controller. (See video!) ...

HypnoKid is an Alternative Mount for the BW 7 Inch TFT Screen. Its counterpart has been modeled to fit a year-old BMW E90/3 Series front seat head-rest - specifically, a 320D in our case. I initially tried mounting it in our '97 VW Sharan VR6 but...

This is a remix of @pedroamz great design for the bigtreetech 2.4" TFT touchscreen https://www.thingiverse.com/thing:3827565. Bigtreetech have changed their hardwaredesign since pedroamz has created his case and some things have been moved like...

I made this to contain a 1.8"TFT screen ST7735 and attach it to a project box which contained an Arduino. The template allowed me to precisely cut out the holes for the cables and the screws to hold it in place and then seal the main box from the...

This is a case for a ST7735 TFT display including the cable connector, and an Arduino Nano or SBC-NodeMCU board. The display as well as the MCU board can be put in place without screws or glue. There's space for several components: * A DHT22...

The overhang makes it a bit of an odd case variant, but it works fine and actually doesn't look bad at all once it is in a case. The situation is that I wanted to use the Pi 2 due to the better performance, which is especially needed when running...

This is a remix of @pedroamz great design for the bigtreetech 2.4" TFT touchscreen https://www.thingiverse.com/thing:3827565. Bigtreetech have changed their hardwaredesign since pedroamz has created his case and some things have been moved like...

This is an Enclosure for Bigtreetech SKR1.3 and TFT35 V2.0 targeted to MPCNC application. BOM: SKR 1.3 TFT 35 V2.0 Fan 40x40 8x Selftapping screws 2.5 x 10 mm You can find the MPCNC modification of BTT TFT35 FW a the following link:...

This fits my clock perfectly, but it was a kind of sloppy kit build, so you will probably want to check the distance between your tubes and the screws on the bottom. I used a gold sharpie to make the letters and graphics easier to see. I tried a...

<p>because europe is at war and my main tube suppliers are from Ukraine i made this Ukraine edition</p>

The diode on the back of my board was too fat to fit the original cover so I remixed it to add a little more space.

ALERT!!!! WORK IN PROGRESS !!!! Thanks to SLD_Maffe and barnestom for their models! 1 - http://www.thingiverse.com/thing:2790589 2 - https://www.thingiverse.com/thing:3475802/apps Just made some adjustments to the case size, added feet, and a...

i created this for z560m tubes and using original socets, printed by prusa i3mk3s Dont need support

Here's a simple little clock case designed for use with a barrel jack, although I've since acquired a smaller Solarbotics/ActiveTech back which I've included in the listing. If you need it in a different size, just let me know and I'll be happy to...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hwU0RHKsP1M

Imprsión en PLA con 0.2 de resolución sin soportes

The diode on the back of my board was too fat to fit the original cover so I remixed it to add a little more space.

I bought the parts from PVelectronics. printed in PETG with 15% infill Treated the surface with 3DXTC epoxy and did a final paint job with rusty paint. ... Front and back plate are from an old wooden box

0.36寸 4位 数码管

The human brain is a marvel of complexity and intricacy, capable of processing vast amounts of information at incredible speeds. Its intricate network of neurons and synapses allows it to learn, adapt, and evolve over time, making it one of the most...

Having upgraded my CR10S with a BTT 35 TFT I was frustrated that the existing Control Box Limited the accessibility of some of the ports and therefore features of the Display. I therefore designed this console to allow access to the Display USB &...