nintendo 2ds grip 3d models

... stick' (or 'joystick') so far. It can also be used for both left and right joy con, so no need to think about which grip your using and you don't have to print two. ... If you want to make a remake you can ask me for files of the basic shapes.

I really loved the idea of the nunchuck style grip but found the front bump didn't do anything, the grip needed to be wider, and farther toward the top. I also moved it to the side so it wasn't uncomfortable when attached to the switch or a center...

I really dug the original design, but felt that the angle was off. ...So, I tweaked it by making the grips run parallel to each other and adding a bit of extra room between them for my fingers to fit comfortably.

Took the excellent modified grip already modified by Joppe and modified it some more - resized to fit better as per some of the suggestions in the comments section. Then I extended it abit so that the button holes would line up properlybutton...

Modified version of the grip to have a native clip. It don't rely on friction to hold the joycon, which give a much better experience of gaming. It is made for printing in PLA. ... I separated the object in 3 parts to glue together in order to...

I tweaked the grip for 3DS created by Suou, and I tailored it to fit perfectly on a DSi console.\r\n\r\nTo learn more about this project, head over to Suou's original work on Thingiverse: https://www.thingiverse.com/thing:2284483

A reimagined version of Redbrumblers' Joycon Grip features a flat top design, perfect for smooth printing without the need for supports. ...When printed at 97% scale, the joycons fit snugly into place, suggesting that an even tighter fit could be...

The shoulder buttons were also adjusted to provide a snugger fit in the grips and a more comfortable feel for your fingers. The fit on my printer is spot-on, but be aware that results may vary depending on your printer. Many users have mentioned...

Back of grip now solid from top to bottom, eliminating an edge that felt awkward when holding If removing the support from the Joy-Con locking mechanism doesn't provide a secure hold (it should), check that upper edges are level and not rounded due...

I was planning to give this as a gift, but every portrait grip I found lacked a floor for the switch to rest and had holes for ventilation, which I didn't appreciate. This design was the best I'd seen so far, but the handles of the model made it...

size has been increased a couple of millimeters to accommodate the new OLED Nintendo switch that has come out. I recommend printing at 45infill or above with tree supports Originally I printed with 20infill and it took 95g of filament. ...

... to avoid sharp edges at the bottom. As soon as I printed it, I will upload a picture. Update: I printed the grip in red PLA with 97% scale and it fits like a glove! Very nice surface thanks to the 45deg orientation of the part. ... Happy printing!

So i was thinking on making this as a gift for a friend but every portrait grip has no floor for the switch to rest and holes for the ventilation wich i don't like it. This was the best i've seen so far but the handles of the model makes it...

I encountered an issue with my printer when attempting to print the joy-con grips, and scaling adjustments within Cura didn't produce the desired results. To overcome this challenge, I modified the attachment mechanism slightly, which significantly...

The supports needed for the Joy-Con locking are already included in the model3) Back of the grip is now solid from top to complete bottom. ...Before, there was an edge that just did not feel right for me, when holding the gripIf, after removing the...

... soon as I finished printing it, I'll be uploading a picture for everyone to see. Update: I just printed the grip in bright red PLA at 97% scale, and it fits perfectly! ...The surface looks fantastic thanks to the clever 45° orientation of the part.

Also rotate it 45° to the back and print with a raft to avoid sharp edges at the bottom.As soon as I printed it, I will upload a picture.Update:I printed the grip in red PLA with 97% scale and it fits like a glove! ...Very nice surface thanks to the...

I printed out several of JGR526's great NS Grip designs. I found V1 and V3 too hard to reach shoulder buttons. V2B was too slim and less grippy. V2A is perfect, however. There is one major problem - the model is mostly split in two halves; see the...

Stand 2DS con las letras incrustadas.

DO NOT CHANGE THE SIZE AT ALLFor 2DS onlyGame storage is separateStand is in a similar style to a Nintendo switch standAssembly requiredSupplies: Super Strong glueAssembly is kinda obvious even if you have the iq of a slice of bread(if you can’t...

The stylus was crafted specifically for use on the Nintendo 2DS handheld gaming console. It was designed using a digital tool called Tinkercad, an online platform that allows users to edit and modify their creations in real-time. ...For those interested...

Original Description: This stand was created specifically for setting up a Nintendo 2DS, as there are limited affordable options available. Print Settings: Resolution: Approximately 0.2mm Infill: Standard Post-Printing: Some edges might require...

Engineers are designing a new 2DS stylus with a smooth, rounded tip for improved user experience.

This wooden case is designed to securely hold a 2DS device. Its interior features a soft felt lining for added protection. Currently, it's still a work in progress. To fabricate the case, print the design using a laser printer on plywood. Secure the...

Nintendo Switch JoyCon Grip wall mount and stand

This model has been tailored from http://www.thingiverse.com/thing:323616 Created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=323616 Settings Utilized: Card count...

This package includes: Element 3D V2.2 in all colors, easy-to-use models and presets. Inside, you'll find one high poly OBJ file, one standard OBJ file, a C4D R12 standard render file, and a 3ds max 2012 standard material file. The E3D file includes...

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=123456\n\n \n \n Instructions\nUsing the following settings:\nbox_height_increase = 10\nnumber_of_strips =...

Let's Get This Party Started! The Ultimate Goal is to have a blast! ... We're talking non-stop excitement, pure energy, and an unforgettable experience that will leave you screaming for more.