nikon z mount 3d models

A simple housing to shield a Nikon S lens mount or a converter.

A 7mm O-ring is suggested to secure the bolt to the mount and prevent it from getting lost when switching mounts or not in use. However, it's not essential; other size o-rings or circlips will work as well, so don't worry about finding the exact...

Adapter to flush mount a Nikon Z DSLR with screws to a ZWO filter wheel. ...No Supports needed for printing.

Nikon Z lens to a camera with C/CS mount. I used this to attach a TTArtisan 50mm/F1.2 lens to a Watec 902H Ultimate low light camera for satellite observations. The lens has very, very short back focus distance, so this adapter brings the camera deep...

Simple cap for Nikon F mount DSLR

This is a versatile adapter that enables Leica LTM and M39 thread lenses to be seamlessly mounted on Nikon Z cameras, unlocking a wide range of creative possibilities. Please note that this adapter has not undergone rigorous testing; its...

Nikon F-Mount Body Cap: Printed With Supports

I have included a 55mm and a 20mm version of working distance from camera sensor to flatfield corrector (which include the 16mm flange distance on the Nikon Z cameras). The 20mm is to allow you to combine it with your own M48 extenders for custom...

Here a cap that fits the Nikon 1 mirrorless system mount.

Modified mounter for Nikon cameras.

Nikon 1 mount for M42 mount, tested on Helios 44M-5 and Helios 44M-2 Flange distance calculated with M42 45,46mm and Nikon 1 17mm, the adapter is exactly 28,46mm high so have that in mind for the tolerances, I honestly don't know much about that.

Nikon 1 mount for M42 mount, tested on Helios 44M-5 and Helios 44M-2 Flange distance calculated with M42 45,46mm and Nikon 1 17mm, the adapter is exactly 28,46mm high so have that in mind for the tolerances, I honestly don't know much about that. ...

Nikon F-Mount body cap. I printed 1st half at 0.1mm and 2nd half at 0.05mm for a better finish. I used supports with the orientation of the nikon logo facing up (as shown in the rendered image). ... Doge donations:...

Nikon F mount Microscope Adapter (Meopta) diameter sdapter 22.9 mm postprocessing depends on the material used Use the adapter in the dark or or use a shade on the adapter

This attaches to the bayonet lugs on the Nikon F mount camera body, safeguarding the interior from dust and scuffs. ...Its design allows it to be printed independently of supports.

This piece fits in to the mount on the top of a lot of Nikon cameras. ...It can be used as a replacement if you lost the cap or as the interface for an accessory.

OpenSCAD files are included for parametric designs of both Nikon male and female f-style bayonet mounts, allowing for potential extender tubes for homemade macro lenses. Always test and tweak for your specific camera. Use manually at ISO 100-200 with...

Create a device that can be attached to a Nikon F-mount camera. ... Looking at the Combo view of the FreeCAD file: A single parameter: Sketch001.Constraints.bottom - allows adjusting the thickness of the mount base (1.5mm is required by "Pocket" for the...

I made a female mount for a Nikon 1-Mount as part of another project and the test part was such a perfect lens cap as it was that I decided to clean it up a bit and make it an actual cap. This cap is a little tight so you might need to sand it a...

simple pinhole lens Nikon f mountprints in about an hour on ender 3 prouse 3d pen or super glue to seal pinhole lens into make pinhole lens take soda can cut it to fit the hole in the adaptor then use a thumb tack to make a small hole in the...

A tripod mount (lens collar) for the Nikon 28-300mm f3.5-5.6 lens. The base is designed as the standard 39mm shoe and fits most systems. Printed in PLA, 30-50% infill. ... You will need a M4 nut and screw to tighten the collar.

... try to fix the overlapping issue. If that fails, I'll lengthen the front for an increased angle. To print, simply download and use support or not! The design is sourced from Nikon's F-mount specifications, while calculations are from mrpinhole.com.

This adapter works with Nikon F Mount lenses, making it easy to integrate them into your existing equipment. The design and testing process ensured a precise fit that is guaranteed to work flawlessly. A clear alignment mark helps you install the...

Used for Nikon D60 camera with Helios 44-2 lens, PETG printing without supports. ...Layer thickness 0.15-0.2 mm

Nikon FT1 Adapter for Nikon 1 to mount to F lenses. ... not tested yet, but it should work

Nikon FT1 Adapter for Nikon 1 to mount to F lenses. ... not tested yet, but it should work

Version 2 boasts better grip, alignment notch, mount type label, and chamfered bayonet lip for effortless printing. With settings at .2 res, 10% infill, and 90mm/s, it takes 50 minutes to complete a print. Both versions fit seamlessly and avoid...

These cases are specifically engineered to securely store Nikon Nikkor Non-AI lenses such as the 135mm, 55mm, 50mm, and 28mm models, with room for lens hoods where needed.

I built this camera mount based on the fantastic Ball and Socket design by Antscran. ...You can see the original model here: https://www.thingiverse.com/thing:2069128

I don't want to pay nor wait for metal extension tubes. ...These are lightweight and I have only designed the body mount part, the other half I stole from someone else so I don't know if they work yet