ng extruder 3d models

I used the mount hole locations from the "KUSBA mount for spite" and used the mount holes from the "adxl343 mount for microswiss" for the location on the NG extruder. ... Can be either used as a press fit as it holds quite well or use a 12mm long...

So I designed my own, this is a direct bolt on replacement to get your NG Extruder onto a MGN12HC linear block using the existing hardware, no extra hardware is needed(besides the rail and carriage block of course). ...There is also a cable...

ADXL343 (Cheaper than 345) mount for the new MicroSwiss NG extruder. A little overkill with heated inserts but hold solid to get an accurate reading. These are the brass inserts I used:...

ADXL343 (Cheaper than 345) mount for the new MicroSwiss NG extruder. A little overkill with heated inserts but hold solid to get an accurate reading. These are the brass inserts I used: ...

BL-Touch/CR-Touch mounting brackets for the Micro Swiss NG Extruder and NG Revo Extruder installed on an ExoSlide motion system.The probe bracket for the regular NG Extruder is different than the NG Revo Extruder probe bracket so print the probe...

This is meant to serve as a starting point for further customization without having to deal with the complicated geometry that the fillets add to the design.I haven't actually test-printed this yet, so YMMV!Original Micro-Swiss model:...

NG extruder fan shroud 5015 adapted since I like to use 0.6 nozzle I also made a volcano adaption for this fan shroud with 5015 blower

... NG Direct Drive Extruder for Creality Ender 6. ... Compatible with: SKU: M3205 (Ender-6 NG Extruder) Use support from build-plate only. Print using PETG, or a more heat-resistant filament. ... MS_NG_ESTEP400.gcode sets the printer E-steps to 400.

Fan shroud for the Micro Swiss NG Extruder for CR-10 V2 and CR-10 V3. SKU: M3206 Cooling Fan (Hotend): 4010 Cooling Fan (Part-Cooling): 5015 This fan shroud does not get in the way or affect of the normal CR-10 V2 / V3 probe mounts. The...

The rear mounting bracket (the tall one) may be resized to fit other extruder setups, but the front bracket is specific to the NG extruder only. The chain I purchased can be found at the link below. You can also search for it by typing the...

Compatible with:Extruder :SKU M3205 - Micro Swiss NG™ Direct Drive Extruder for Creality Ender 6 PrintersHotend: Micro Swiss All Metal HotendHotend Fan: 4010Part Cooling Fan: 4010 BlowerProbe: none3D Printer Model:Ender-6

This is a remix of the Micro Swiss NG shroud https://www.thingiverse.com/thing:5358828 for use with a 4020 blower fan. So, it is fully compatible with CR10s Pro V1 & V2 fan's. I also modified the top right side of the shroud to place the...

I didn't like the BLTouch bracket I got with the NG as I felt the BLTouch tip was too low during printing. One print that went a bit weird and overextruded actually broke my probe! ... Adjusted it to raise the BLTouch probe tip by 1mm, so the Z offset...

This is a remix of the Micro-Swiss model which retains all of the critical geometry, but greatly simplifies the model by removing the fillets. This is meant to serve as a starting point for further customization without having to deal with the...

I mounted an extremely powerful 40x40x10 fan to cool the hotend ( Sunon MF40102VX-1Q03C-A99 ) which causes a kind of venturi effect which blows air in the direction of the bottom left bed, which caused some problems to print ABS,Nylon,PC.. I...

Fan shroud and probe brackets for the Micro Swiss NG Extruder for CR-10/Ender-3. Use support from build-plate only. Print using PETG filament or something even more heat resistant. The probe brackets attach to the NG main body using flat-head...

This appears to work fine with the stock extruder or with the regular Micro Swiss direct drive extruder, but it does not work with the NG extruder. It causes the endstop to collide with the fan shroud, so if you're using the NG extruder the limit...

Fan Shroud, Probe Brackets and Endstop Bracket STL files For Micro Swiss NG Extruder for Ender-5, Ender-5 Pro and Ender-5 Plus. Compatible with: SKU: M3202 (Standard V-Roller Edition) SKU: M3204 (Linear Rail Edition) Use support from...

This is a fan shroud with a 5.5mm microscope mount for the Micro Swiss NG extruder. Made by modifying the official Microswiss Fanschrode STEP file. It is designed to allow the scope to go through the vents of the part cooling fan, but does not...

This is a remix from https://www.thingiverse.com/thing:5781987 and https://www.thingiverse.com/thing:5393935. With Klipper the printing speeds are very high and the filament must cool very quickly. After drawing 4020 to 5015 and 4020 to 5020...

Compatible with:Extruder :SKU M3201 - Micro Swiss NG™ Direct Drive Extruder for Creality CR-10 / Ender 3 PrintersSKU M3203 - Micro Swiss NG™ Direct Drive Extruder for Creality CR-10 / Ender 3 Printers (Linear Rail Edition)Hotend: Micro Swiss All...

my remix of the micro swiss NG shroud for use with a 5015 blower fan. Should be compatible with CR10, CR10s, CR10s Pro or similar with a 5015 fan. ... Hardware required: 2 x M3 nuts 2 x M3 20mm screws 2 x M3 washers Fully tested, updated to remove...

From my remix https://www.thingiverse.com/thing:5393935 of the original Micro swiss NG Shroud https://www.thingiverse.com/thing:5358828, I re- adapted the design to add a 50x7mm COB LED Strip Chip On Board. It is possible to cut and sand the strip...

my remix of the micro swiss NG shroud for use with a 5015 blower fan. Should be compatible with CR10, CR10s, CR10s Pro or similar with a 5015 fan. Updated to remove excess nut retainer to allow mounting screw to be directly accessed in rear,...

Now with adjustable support and compatible with dual extruder sharebot NG. VERY IMPORTANT. You'll need to remove the LCD screen if you want to save most of the print area since the fans are now in a decent position for cooling. Btw this is now a...

Verify that this matches your NG Extruder model number before printing out any of these parts. When printing the fan shroud, use support from build-plate only. Print using PETG, or a more heat-resistant filament. RESTORE_DEFAULTS.gcode...

Verify that you have the M3302 NG Extruder model number before printing out any of these parts. When printing the fan shroud, use support from build-plate only. Print using PETG, or a more heat-resistant filament. ...

Print in ABS if possible

This is a fast and dirty fusion 360 model based on the Micro Swiss NG direct drive. The adapter is made to allow the use of a 5015 blower instead of the stock blower fan. The print requires support. I used cura 5.0 with tree supports and it...