next level racing f gt 3d models

Next Level Racing F-GT Lite - PS5 controller holder

A cupholder for the Next Level Racing F-GT Lite racing seat I designed for my brother who's into sim-racing :)

This is a 200 mm long clamp to attach the pedal plate to the seat frame of the Next Level Racing F-GT Lite. I made this prevent the pedal plate from sliding left towards the clutch under heavy braking. I used PETG. This clamp uses 5 each M5x30mm...

Designed this cupholder for my brother's sim racing seat :)

The spacer goes in the empty hole to allow you to torque down the third bolt without bending the shifter plate.Needs 3x M8x60 boltsBased on a reddit thread by...

This is a 22mm hub spacer to mount the shifter clamp for additional reach on the right side of the rig. I used PETG. NOTE: This part is designed for 50% over-extrusion. ...I included my cura profile for reference.

These are replacement grommets for the Next Level Racing, GT-Lite and F-GT Lite. There is no latching mechanism, they were designed to be a tight fit and held in with the layer lines, you can add glue if needed. ...I printed these in PETG.

This print allows you to mount a (or two, in my case) [Sinuslive Bass-Pump III](https://www.conrad.com/p/sinuslive-bass-pump-iii-exciter-speaker-130-mm-80-w-8-378284) bass transducer to your Next Level Racing *GT Lite* or *F-GT Lite* foldable racing...

While the shifter mount plate on the Next Level Racing GT Lite and F-GT Lite racing chairs is compatible with the Fanatec shifter, it doesn't actually fit if you mount the hand brake to it. The bottom of the handbrake is then slightly below the...

This is an extension plate for use with the shifter mount on the Next Level Racing sim cockpit, specifically for use with the Fanatec Clubsport SQ v1.5 sequential and h-pattern shifter. It brings the shifter closer to the driver, usually most...

This is an extension plate for use with the shifter mount on the Next Level Racing sim cockpit, specifically for use with the Fanatec Clubsport SQ v1.5 sequential and h-pattern shifter. It brings the shifter closer to the driver, usually most...

Extension plate for Fanatec Shifter for the F-GT Next Level Racing Sim Racing rig. You may find you smash your hands into the rig when it's in the normal slots. ... Printed on its side no supports

Shifter mount for CSR H Pattern Shifter This was designed for the Next Level Racing F-GT Lite mount. ... you will require m6 bolts ~20mm and some m10 bolts ~110-120mm M12 version requires M12 bolts 110mm

A simple mount for transducers on the back of the seat for the Next level racing f-gt Printed with 50% infill I used a m6 screw and nut.

I made a handbrake holder for the Next level racing F-GT formula position. It may need a remix to clean it up if someone wants to do it, but for me it works well on my rig. ... Printed with 50% infill and tree supports.

A Simple Fix to Attach a Bass Shaker to Your Next Level Racing F-GT Rig Without Drilling Any Holes. ... Get the full scoop on how it's done in this video: https://youtu.be/al3gEAN6RiI You'll need 4x 60mm M8 bolts and 4x M8 nuts to get started.

Basically a tool to connect your stick shift to the next level racing GT lite chair

I've recently dipped my heel-toes into simracing... This led me to the decision that I can't truly simulate driving a race car without a cup holder and a phone mount. The cup holder is pretty straight forward, although a little bit on the larger...

Remix of Phanton25's button box for the Next Level Racing F-GT Lite. Step files included for your own buttons, encoders etc. Buttons I used were 13mm, while encoders were 7mm. I recommend adding filets to the mounting squares as I recently...

Cable organizer designed to fit the Next Level Racing F-GT Lite and Logitech G29 racing wheel with shifter. The medium clips onto ~25mm tubing and hold 4 cables approximately 4mm in diameter. Small fits on the bends, large fits on the adjustable...

... my design. ...This is a toolless power supply mount to attach the Moza Racing R5 Power supply to the Next Level Racing GT Lite.Mounts are tight enough to prevent the power supply from sliding and hold securely to the NLR GT-L even while folding

What I needed though was a way to mount it to my Next Level Racing GT Ultimate wheel stand. The problem though is I use the tube mounts for shifters and joysticks. I needed a solution that would let me get more secure mounting space on the wheel...

Hi Next Level Racers! I've been wanting to do this for a while and had printed the fantastic stream cheap https://www.thingiverse.com/thing:2822140 by DaveM before. What I needed though was a way to mount it to my Next Level Racing GT Ultimate wheel...

Hi Internet Sim Racers, Those with an Next Level Racing rig will know the pain of the adaptor arms going limp and floppy when those cheap plastic bung's start to give out... typically just 10 seconds after you've slide the arm in. So being sick of...

Hi Internet Sim Racers, Those with an Next Level Racing rig will know the agony of the adaptor arms going slack and flaccid when those cheap plastic inserts start to fail... typically just 10 seconds after you've slid the arm in. So tired of the...

Cable organizer designed to fit the Next Level Racing F-GT Lite and Logitech G29 racing wheel with shifter. The medium clips onto ~25mm tubing and hold 4 cables approximately 4mm in diameter. Small fits on the bends, large fits on the adjustable...

Endcaps for Next Level Racing Elite and 8040 aluminium extrude

Simple wrench for the handknobs on Next Level Racing cockpits, some times they are very hard to unscrew by hand.Please do not over tighten the screws with the wrench or the handknobs will shatter. print this with a good amount of infill.

good

A Simple cable clip for the Next Level Racing GTtrack